Messages

331

General Mach Discussion / Re: Need some help with new build... Reset Gecko G320 fault causes Y axis to move?

« on: April 06, 2009, 11:42:52 AM »

Hi, Radioactive

Sound's like you have a Plugin running, SStepper or Gaila, They need to be turned OFF under General, Control PlugIns, Then Re-Start Mach3..

Chip

332

LazyTurn / Re: LazyTurn

« on: April 06, 2009, 12:38:49 AM »

Hi, Rich

Wooo  Hooo  , I'll send you my address.

Edit: Ooo I read it Just Fine, Big print Giv-Ith, nobody reads the fine Print.

Ask "Art" about that, Something about, "First Born"

Chip

333

General Mach Discussion / Re: Need some help with new build... Reset Gecko G320 fault causes Y axis to move?

« on: April 06, 2009, 12:23:44 AM »

Hi, Radioactive

Make sure you have Port "1" selected in port's & pin's, Motor Output's for Dir & Step Port's.

Also do you have a Pulse Frequency showin on the Diag. screen.

Chip

334

LazyTurn / Re: LazyTurn

« on: April 05, 2009, 11:53:14 PM »

Hi, Rich

Or this with LazyCam.

N5 G80
N10 G0  X0.0000  Z0.0000
N15 M3
N20 G1  X0.2500   F60.00
N25  X0.5000  Z-0.2500 
N30  Z-0.5000 
N35  X0.7500   
N40 G3  X1.0000  Z-0.7500  I0.0000  k-0.2500
N45 G1  Z-1.0000 
N50  X0.5000   
N55  Z-1.3749 
N60 G2  X0.6250  Z-1.4999  I0.1250  k0.0000
N65 G1  X1.0000  Z-1.5000 
N70  Z-1.7500 
N75 G3  X0.7500  Z-2.0000  I-0.2500  k0.0000
N80 G1  X0.6250   
N85 G2  X0.5000  Z-2.1250  I0.0000  k-0.1250
N90 G1  Z-2.5000 
N95  X1.0000  ;X0.0000 mod 
N100 M30

Chip 

335

LazyTurn / Re: LazyTurn

« on: April 05, 2009, 11:14:07 PM »

Hi, Rich

I've pretty much tried all those The only one that almost get's it is Center, LH then RH Tool.

It'3 Gremlin's, I know what you mean for sure, Making it Lazy.isn't Easy at All.

Chip 

336

LazyTurn / Re: LazyTurn

« on: April 05, 2009, 10:37:31 PM »

Hi, Rich

Use the 35 deg tool in Center mode first, Then LH & RH tools.

Doesn't seem to bother anyone that the RH tool part's off the work with Rough pass, I Guess.

Thanks, Chip

337

General Mach Discussion / Re: Need some help with new build... Reset Gecko G320 fault causes Y axis to move?

« on: April 05, 2009, 10:29:51 PM »

Hi, Radioactive

Swap the A B wires that should fix it, But sound's like you have the Enable terminal held in Reset all the time.

You should only apply 5 volt power to it to Reset the drive's. Re-read over the paper work.

Chip

338

General Mach Discussion / Re: new computer can't jog faster than 50 ipm?

« on: April 05, 2009, 05:10:11 PM »

Hi, Rusty

Sent you a PM message, Top left of this screen, Click on your messages.

Chip

339

LazyCam (Beta) / Re: Posting Code Not Work all time

« on: April 04, 2009, 03:26:12 PM »

Hi, AndresRubio

To generated offset or Pocket's, You need a LazyCam License.

Chip

340

LazyTurn / Re: LazyTurn

« on: April 04, 2009, 03:17:25 PM »

Hi, Art

I was only using the different cut values and offset's to show the Differences in the Rough passes.

Thanks for taking a look at it.

Chip