Hello Guest it is September 21, 2023, 12:09:22 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Chip

321
General Mach Discussion / Re: Problems threading on the lathe
« on: April 10, 2009, 08:07:05 PM »
Hi, Art

Not getting an RPM output hear until I put pulley ratio to .001, See picture bellow for details, Expanded RPM Dro display.

Using your exe and driver with simulated 555 timer setup hear.

Chip

322
General Mach Discussion / Re: Feedrate Overides in Lathe
« on: April 10, 2009, 12:04:02 AM »
Hi, Danny

Did you get things working, Just updated/cleaned up the lathe.set a bit Above, Let us know.

Chip

323
LazyCam (Beta) / Re: Changiing Layer names
« on: April 07, 2009, 07:08:20 PM »
Hi, Dshowalt

When you move a Chain to a new layer, You can name it whatever you want, See pic's below.

Click on left hand project window "Chain", Then right click on it will geve you the Option."

Chip

324
General Mach Discussion / Re: One pc two machines
« on: April 07, 2009, 04:00:11 PM »
Hi, Spnar

If you right click on your Mach3 "Icon" and change the Target line to as shown in the first pic, Don't forget the Apple & OK, You'll get this Menu at Mach start-up, To chose a Profile Name, 2'nd pic.

Hope this Helps, Chip

325
General Mach Discussion / Re: Feedrate Overides in Lathe
« on: April 07, 2009, 01:45:32 PM »
Hi, Danny

Hears the Lathe. lset file, Install it in C:Mach3 folder, It's a work in progress screen Lset.

You need also install the Zip file (JPG's) in C:\Mach3\Bitmaps\MillBitmaps folder.

Edit: New 1024 CHIP LATHE D1ACC.set some added items.

Have Fun, Chip

326
General Mach Discussion / Re: Feedrate Overides in Lathe
« on: April 07, 2009, 01:23:58 AM »
Hi, Danny

I use a Modified Mach3mill.set (screen set) and changed the .set to Lset file type all the over-rides work just fine.

Chip

327
LazyTurn / Re: LazyTurn
« on: April 07, 2009, 01:09:03 AM »
Hi, Marcel

Yes I've used a cut-off/grooving tool quite often, Were just going through roughing using multiple tool's and where it's missing the roughing passes.

Have you looked over LazyTurn posts, It's coming along nice I think.

Got that square cube on Friday, Now that is some kinda Nice Work Your Doing, Thanks  for sharing it with me, Finding a special spot for it.  :D

Thanks, Chip

328
Hi, Radioactive

Good to hear, Let the games begin.

Chip

329
General Mach Discussion / Re: One driver two motors
« on: April 06, 2009, 07:45:09 PM »
Hi, Spatch

I've seen it done a couple of time's, If it's on a common shaft alignment is critical, It it's on separate shaft's like a dual gantry type install it pretty much a homing issue of needing to home to a hard Stop. As far as I know most would not recommend it as a common practice.

Chip

330
Hi, Radioactive

If your not running Warp9 Smooth-Stepper Board, It's a USB device, When you start Mach3 select the Normal Printer Port Control, Then verify that SStepper Plugin is X'd out in Plugin's page.

PM message your phone # by clicking on my user name, I'll give you a call tonight at 9:00 FL time, If your in US or CA.

Chip