Messages

1741

LazyCam (Beta) / Re: Set chain Depth button

« on: February 02, 2007, 09:39:10 PM »

Hi, Elcam

This problem has existed for some time, It doesn't bother some computers, It has been an on-again, off-again problem for me.

This is a on-going development program, Use the right hand lower Layer/Object Porop... for entering your cut depth, each layer has

only one depth, if you need different depth on an item right click on it, assign it to a different layer.

Use the Set origin min button to set origin, it works fine you just cant move into the drawing.

Brian posted, It may be a Graphics Issue causing this, Fix in the works I hope.
 
Hope this Helps, Chip

1742

LazyCam (Beta) / Re: relocating x0 y0 start position

« on: February 01, 2007, 10:43:13 PM »

Hi, Brian

This is what Debug shows.

Thanks, Chip

1743

LazyCam (Beta) / Re: shut down message

« on: February 01, 2007, 10:13:46 PM »

Hi, Terry

This problem has existed for some time, It doesn't bother some computers, It has been an on-again, off-again problem for me.

The best you can do is use the Reset Origin Min Button for now.

Hope this Helps, Chip

1744

LazyCam (Beta) / Re: relocating x0 y0 start position

« on: February 01, 2007, 03:32:00 PM »

Hi, Bill, Brett

This problem has existed for some time, It doesn't bother some computers, It has been an on-again, off-again problem for me.

There was a way in earlier ver to set it in the right # enter origin manually, don't now where it went, ill look back in ver's.

More Info, Chip

1745

General Mach Discussion / Re: Trouble With Program

« on: February 01, 2007, 01:34:50 AM »

Hi, pzzamakr

Your G-code had a G92 x10 y10 y10 which I put a note on, Remarked it out about 5 lines down.

It runs hear I don't hane your tool data.

Dry run it,

It needs more editing I would think.

Hope this Helps, Chip

1746

General Mach Discussion / Re: Motors turn in Kcam, but not mach. What on earth am I doing wrong?

« on: January 31, 2007, 10:51:07 PM »

Hi, CJ

Try this XML, it shows port active couldn't get yours to work, no port output in Diag.

Hope this Helps, Chip

1747

LazyCam (Beta) / Re: Can't open dxf files...

« on: January 30, 2007, 12:37:24 AM »

Hi, Dre

I thought it was stand-alone, it may like the folder name Mach3.

Glad you got it working, Chip

1748

LazyCam (Beta) / Re: Tool Offsets

« on: January 30, 2007, 12:15:55 AM »

Hi, FastCote

In Mach3 set tool settings in tool table, Offsets screen, bottom right.

Hope this Helps, Chip

1749

General Mach Discussion / Re: Hypertherm remote start with hand torch?

« on: January 30, 2007, 12:10:09 AM »

Hi, Dave

It's sad miller posts there manuals in PDF's for Free.

Hope you get it going.

Thanks, Chip

1750

LazyCam (Beta) / Re: Can't open dxf files...

« on: January 29, 2007, 11:56:40 PM »

Hi, Dre

The DXF file I sent Works for sure.

I'll think on it tonight sea-ya tomorrow Pm.

Try setting in windows, system, advanced, performance, settings, advanced, processor scheduling, to Background

In early LasyCam there was a DLL file that was missing that caused problems also, I'll think on it tonight, also.
 
Sorry we havent got you working yet.!! Thanks Chip

What ver of Mach3 and LazyCam are you using, Check under, Help, About