Messages

171

MACH TOOL BOX / Re: MACRO , Tool Table Report

« on: July 13, 2009, 11:56:32 PM »

Hi Terry

Thanks for sharing all these M1S files, It gives us allot of good examples to work with and put to use.

I see on this one you've used the name ToolTableReport,m1s, Is this allowed in the Mach3 Rev. 4 your testing ?.

Hopping it is and maybe some day some of us will get a Look at it Hear.

Thanks, Chip

172

General Mach Discussion / Re: Configuration problem with EStop

« on: July 13, 2009, 09:05:05 PM »

Hi, Dana

In Config, Ports & Pins, Inputs, E-Stop change the "check" to "X", See pic.

Chip

173

General Mach Discussion / Re: Random -Z (going down WAY too far!!!)

« on: July 12, 2009, 06:51:26 PM »

Hi, Rich

Re-check your ver. of LCam, It works fine hear.

Chip

174

General Mach Discussion / Re: motor does not run

« on: July 11, 2009, 09:17:15 PM »

Hi, Garhar1

It may be a LowActive setting issue for the one dir only problem, You'd think the MFG's would do a better job with a "link" to Good setup files.

Just use the pin numbers that move the X axis and change them from Z to X axis in Ports & pins.

Hears the Manual I think for your board, Sending a PM message to you.

Chip

175

General Mach Discussion / Re: motor does not run

« on: July 11, 2009, 05:03:55 PM »

Hi, Garhar1

I responded to the same Question in FAQ section, http://www.machsupport.com/forum/index.php/topic,12032.0.html.

Please don't post the same question all over the place.

Thanks, Chip

176

FAQs / Re: motor don't move

« on: July 11, 2009, 04:51:11 PM »

Hi, Garhar1

I think this board needs to run in Sherline 1/2 step mode in Mach3, See pic 1, There should be 3 Jumper on ENA# just above (X,Y,Z,) Axis Labels also pic 2.

Chip

177

General Mach Discussion / Re: Mach3 error: No Shuttle of type selected

« on: July 10, 2009, 08:02:43 PM »

Hi, Dbvogt

You can change the Active Low state to this in Ports & Pins,  Then Mach will reset, But in the end you still need to get a E-Stop pin assigned and working.

Chip

178

General Mach Discussion / Re: machine pauses after spindle/laser is triggerd

« on: July 10, 2009, 07:23:42 PM »

Hi, Dave

No just the delay setting's, There is a post on this issue, I'll try to find it, Hear it is, I don't think it was ever resolved though.

 http://www.machsupport.com/forum/index.php/topic,9086.0.html

179

General Mach Discussion / Re: machine pauses after spindle/laser is triggerd

« on: July 10, 2009, 02:56:18 PM »

Hi, Dave

Have you checked the Spindle Setup in Port' & Pin's setting's.

Chip

180

General Mach Discussion / Re: Need help Mach 3 Version R2.63 on MW XP HOME w/SP3

« on: July 10, 2009, 12:42:30 AM »

Hi, Fp5757

For the most part Mach3 is happy where ever you install it, The default location is C:\Mach3, Over the year's I've had this issue maybe 3 time's in many many many installs. There is a major rewrite that Brian is doing that should be out soon "Mach3 ver. 4".

I'm sure someone will comment as to the language it uses soon.

Chip