Hello Guest it is September 21, 2023, 10:39:33 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Chip

General Mach Discussion / Re: Rutex and Mach3 problem
« on: March 31, 2007, 04:13:07 PM »
Hi, Keith

I've used the rutex Boards sending you a Personal msg.


LazyCam (Beta) / Re: Optimization doesn't seem to be working.
« on: March 30, 2007, 06:27:46 PM »
Hi, Gabriel

Running latest Ver. of LC, Working hear, Under AutoClean Settings, Do you have Optimise Drawing "Checked".

Post your sorce file you load into LC, or let us now the extension for the one you posted last.

Thanks, Chip

LazyCam (Beta) / Re: Lcam Pro Purchase
« on: March 30, 2007, 06:13:29 PM »

LazyCam (Beta) / Re: Lcam Pro Purchase
« on: March 30, 2007, 03:11:03 PM »
Hi, Socalcnc

It's under Downloads Above, "plug-ins".

Hope this gets you there, Chip

LazyCam (Beta) / Re: Lazy Cam Pro
« on: March 29, 2007, 03:07:21 PM »
Hi, Brian

I try ed the Rev. Arc as you stated, Just big circles with that.

It's not just the Arc's, First straight line are cutting deepest cut's first.

My Turn Options are X mode Diameter "checked" and Rev. Arc's in Front "checked", Had to edit code missing G01 at bottom of code.

I'll post screen shot with courser cut's smaller DXF and Tap Files.

Thanks, Chip

OK, Thanks

LazyCam (Beta) / Re: Lazy Cam Pro
« on: March 28, 2007, 02:22:46 AM »
Hi, Art, Brian

Turn is going to be "Nice".

Mach3R2.00.061, There seem to be some line confusion and several G02, G03 Raid errors Mem out, WOW !!, What a Start for Turn.

Thanks, Chip

General Mach Discussion / Re: Can Mach3 be run with Mach2 driver??
« on: March 25, 2007, 02:04:49 AM »
Hi, Werner

No, but both can co-exist on your computer, Allowing Mach2 and Mach3 to be used.

Hope this Helps, Chip

Hi, Dave

As Hood stated, An option, I think if you look at the Wiring Diag's on those machines you'll find the limit SW's kill motor power and pause the control.

If your using NC switches, Reset wont reset if any of the switches are open, better than a dirty contact on an NO SW not working.

Thanks, Chip

LazyCam (Beta) / Re: Confused about LCAM versions
« on: March 23, 2007, 01:44:24 PM »
Hi, Elnino

What you stated is mostly true, For latest ver of LazyCam D-load Mach3R2.00.060 or latest Ver above under Downloads, "Mach releases".

Optimize is working in D-load ver, LC has been split into Std., Pro ver, Pro requires a License, Downloads, "Plugins", for Pocketing, Lathe,

Offsets, ........

Hope this Helps, Chip

LazyCam (Beta) / Re: Lazy Cam Pro
« on: March 23, 2007, 01:25:14 PM »
Hi, Gabriel

LazyCam Pro is in latest down load of Mach3R2.00.060.

To use the added features you need a license, Look in Downloads, Plugins above.

From what I've gathered a $50.00 fee which will be good for final release Ver, Will increase to $100.00 sometime in the future.

Hope this Helps, Chip