Hello Guest it is September 21, 2023, 11:50:34 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Chip

LazyCam (Beta) / Re: LazyCam 2.01 Lathe
« on: May 25, 2007, 09:49:22 PM »
Hi, Wnevels

Hear you go wasn't paying attention hear, I think this is it.

Thanks Chip

LazyCam (Beta) / Re: LazyCam 2.01 Lathe
« on: May 25, 2007, 09:34:48 PM »
Hi, Wnevels

It's right below the first picture, second Red Download Button.

Thanks Chip

LazyCam (Beta) / Re: LazyCam - newbie questions
« on: May 24, 2007, 08:35:55 PM »
Hi, Ken

2.02 has LC Pro built in, You just need the license to turn it On, Top of this screen, Downloads, Plugins, 2nd Item down.

"This upgrade license is emailed within 24 hours and enables the PRO level features of LazyCam. Pocketing, Offsetting, Turning and primary Foam functions. It will be added to over time , and is offered at an intial pricing  for the upgrade license file. Its price will increase as its functionality increases, but licensed users get updates at no charge.  Current price - $75.00 US".

There really isn't much in the way of doc's, It's changing to fast.

There is a video, lot's of changes there also.

Should be a New video out Soon.

I'm sure you'll like it, Chip



Competitions / Re: ******Guess and win a G100 Grex******
« on: May 23, 2007, 10:29:46 PM »
Hi, All

Until I do a re-count, it's 2,760,082, There's some pretty small chip's in there, My eye's hurt now.

Hope I'm Close, Chip

Who's going to do the re-count, Could be some hanging chip's/chad's in there.

LazyCam (Beta) / Re: Not Loading DXF
« on: May 23, 2007, 09:57:16 PM »
Hi, Jim

I had a file like this, I'm loading your's now, it looks like LC isn't working on it but it is, it took about 2 min. to load with a 1,666 Mhz computer with 1,256 Meg's of ram check your windows task manager, you'll see its working at 100 %, It may even say Not Responding, Not true there a zillion little moves in this file see the view below is this it. ??  There are 12,562 entities in this file.

Thanks, Chip

LazyCam (Beta) / Re: z axis keeps moving up and down!! please help
« on: May 23, 2007, 09:13:50 PM »
Hi, Nose

Download LC now I think it's fixed give it a try, Was going to post this eariler got sidetracked.

LazyCam is posting an incorrect G0 Z Move's It's set to Z 60.000 hear, It's a Bug.

You can Edit it out in your Tap File in Mach, Edit then in Editor, Edit, Find "G0 Z", change the value to your desired G0 Z value (such as Z0.0000 or a safe Hight of Z0.1000 would be .1 units above your Z0 top of cut surface).

Thanks, Chip

LazyCam (Beta) / Re: Lcam Rev 2.02
« on: May 23, 2007, 12:23:49 PM »
Hi, Brian

Just downloaded 2.02 LazyCam, That fixed the plasma file load problem, Thanks.

Look's like you did some work on Lathe Code also,Thanks !!

In Mill Mode, The Info Layers, "Cut" send/set to "All Layers", Isn't working.

In Plasma Mode, It's looking Purity Good. !!

In Lathe Mode, See Example's in later Post.

Your "S" key "Rat" is much bigger in Plasma mode than Mill mode and still lock's UP, I no it's just test stuff now.

Thanks, Chip

Hi, Willem

Looked at it today, It's not All Files, Just Some of them.

Thanks, Chip

LazyCam (Beta) / Re: Lcam Rev 2.02
« on: May 22, 2007, 10:46:54 AM »
Hi, Brian

In plasma mode while loading the above file, "test55Dotpolyline2.DXF"

I'm getting a UnRecoverable Error in "DrawStock" and Lazycam shuts down.

Work's fine in Mill Mode

Thanks, Chip

Hi, Willem

I got the same Error Msg. but with a file of mine, It dose it with all files i'v tried.

Thanks, Chip