Messages

1521

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 05, 2007, 04:24:55 PM »

Hi, Brian

Using LC downloaded this morning, Hears a list of what I see using the below DXF and Lcam files.

I found the outer box in My drawing was not closed so its a new file, It was causing LC not to generate Offsets.

Offset's: LC is placing offsets backwards hear Out's- In, In's- Out, The Spline Upper right produces a Giant Circle when Offset is used, It's picked up in Pocket's Chain 11 for cut.

If there are two Offset Chain's from the same layer #, Chain #, only one "The First one will highlight when Clicked on" in rotated/side view, The second one can be adjusted, deleted even though it doesn't Highlight. If there on top of each other no highlight for ether. 

Circle will not select with mouse click, will select in project window though.

Pocket's: Misses the Spline Upper right all the time, I now it's probably the Importer, Any up-date on it. ?.

Would it be possible to add the ability in Projects Window to allow adding comments or re-naming, Layers, Chain's and Pocket's, With the Right Click Mouse Option ?

Could there be a way to select Chain's in Projects Window the same way as Single/Multiple Select Option and move them to a "Drill/Other" Layer. ? 

All In All Working Pretty Nice.

Thanks, Chip

1522

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 03, 2007, 07:07:29 PM »

Hi, Brian

Just downloaded, It' creating Island's, But no Pocket's with "create islands" un-checked.

Thanks, Chip

1523

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 03, 2007, 03:05:20 AM »

Hi, Art & Brian

Getting very different results with LC 2.05 and LC 2.02, It's a small file using .0625 for tool dir.

Offsetting objects first then Pocketing, LC 2.05 not consistent at all hear.

Thanks, Chip

1524

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 02, 2007, 12:30:36 PM »

Hi, Art

Been working with Paul's file hear, For a while, If I set an outside offset at .125, I couldn't set a inside offset of .125, It would set a inside off set of .0625 though and after that I could set the .125 inside offset just fine.

Now inside and outsides is working fine.

It's now flaky again hear.

Mabey a clew in this, Chip

1525

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 02, 2007, 02:16:35 AM »

Hi, Paul

I set the drill's for .070 with .010 step down, thy show the step down but don't drill as thy should though, No Peck action.

Did you find the .Tap file at LazyCam 2.02 page 4.

Gone for the night Hear, Chip

PM your Phone #, I'll give you a call today, I think the Clock is off on the site it's 2:15 Hear.

Art, thanks for the early Look.

1526

LazyCam (Beta) / Re: Download lazycam...having problem with importing a DXF

« on: June 02, 2007, 01:56:24 AM »

Hi, All

Tryed it hear, LC 2.05, TurboCad V8, BobCad V18, no Joy.

Rino opened it, Saved it as acad 2000 & R14, Loads in LC now.

Hope this Helps, Chip

1527

General Mach Discussion / Re: PROBLEM WIT LAZY CAM

« on: June 02, 2007, 12:57:57 AM »

Hi, Franco

I was running with 256 K on a 1.666 Comp. hear, Put in 1.256 K now,  Makes a big Difference, Many program's open, Mem dosn't seem to ever get above 800k.

Some file's are Huge and thy take time to Crunch.

Post your File.

Thanks, Chip 

1528

LazyCam (Beta) / Re: Lcam Rev 2.02

« on: June 01, 2007, 11:43:35 PM »

Hi, Brian

Upload Options hear, instead of Ziping it and uploading.

Thank, Chip

1529

LazyCam (Beta) / Re: LCam Pro ver 2.05

« on: June 01, 2007, 11:36:46 PM »

Hi, Paul

Try this .Lcam file, I think it's sorta what your looking for.

Thanks, Chip

1530

LazyCam (Beta) / Re: Lcam Rev 2.02

« on: June 01, 2007, 11:28:10 PM »

Hi, Brian

Just started to work with it.

Can .Lcam be added to Attachment Options. ?

The load and post to mach seem to be working now.

Thanks, Chip