Messages

1511

LazyCam (Beta) / Re: newbie needs some help

« on: June 13, 2007, 01:45:39 PM »

Hi, Nose

Hears a couple of files, The biggest problem with your file is there are many unconnected and non trimmed overlapping lines.

There are some issues with LCam picking up line segments that are grouped also.

This is a work in progress, There are some import options that are being worked on by an outside vendor for LCam.

Hope this will Help, Chip

1512

General Mach Discussion / Re: Mach-3 interface questosn

« on: June 13, 2007, 12:18:39 AM »

Hi, Bertho

Not knowing how your Magnetic sensors are wired, Thy may still be floating a low or high signal that close, Try adding a 2000 ohm resistor to there output to

Gnd. or +5 volts holding them hi or lo, Until a stronger signal pull them full on or off.

Using some Prox switches hear, There Opto Isolated and have a Pull down resistor on the switch side.

Hope this Helps, Chip

1513

LazyCam (Beta) / Re: newbie needs some help

« on: June 12, 2007, 11:58:50 PM »

Hi, Nose

Waited some time four your file to load never finished hear.

Loaded it into Turbocad 8 Grouped All saved loads hear now.

Hears the New dxf, NC and Lcam files, Give them a try.

Hope this Helps, Chip

1514

General Mach Discussion / Re: Mach-3 interface questosn

« on: June 12, 2007, 10:08:55 PM »

Hi, Bertho

So whats not working at this time, The normal Condition is to be set as normal after you get everything working, Art has some key items that if you change

them it trigger abnormal condition.

I have no idea if or where theres a list on the items.

Thanks, Chip

1515

General Mach Discussion / Re: Screen 4 for lathe

« on: June 12, 2007, 09:57:35 PM »

Hi, Hood & Mark

Looks like it works

Working on the Lset when time permits, enjoy.

Thanks, Chip

1516

General Mach Discussion / Re: Mach-3 interface questosn

« on: June 12, 2007, 11:08:35 AM »

Hi, Bertho

If your refereeing to the "Normal Condition" Button flashing, If everything is working normally now except for the flashing Button.

Click on it and Yes to set Normal Condition, It won't flash again unless you've changed settings after reseting it.

Hope I didn't miss the Point hear, Chip

1517

General Mach Discussion / Re: Screen 4 for lathe

« on: June 12, 2007, 10:24:55 AM »

Hi, Mark

Hears a Turn.Lset based on mill screens with added big screen and Lathe Tab pop-out MPG, It's a work in progress .Lset

Had to Zip it, Hay Brian when you get time could you Add .Lset to file Up-Load Options Hear, Thanks.

Hope this Helps, Chip

1518

General Mach Discussion / Re: magnetic home switches

« on: June 12, 2007, 09:17:43 AM »

Hi, Stirling

If your Debounce is at 0 set it to 2000 - 4000 may solve this problem, Config, General Config, "Debounce Interval" 2000.

Hope this Helps, Chip

1519

General Mach Discussion / Re: Spindle direction control

« on: June 11, 2007, 02:28:11 PM »

Hi, Tmsmith

If your not getting a change of state on your Pin's, Change the LowActive State from X to Check or Check to X as needed for your Dir pin anyway.

Hope this Helps, Chip

1520

LazyCam (Beta) / Re: OK, I give up! How do I get ACAD dxf files to open in LCAM 2.02?

« on: June 08, 2007, 11:16:31 PM »

Hi, Cody

Your file loaded with latest ver of LC, The Offsets, Optimize and Clean aren't working very well though.

Hears a Lcam file, Your DXF took a while to load.

Hope this helps, Chip