Messages

1451

LazyCam (Beta) / LazyCam 2.02

« on: July 12, 2007, 10:45:32 PM »

Hi, Art & Brian

Very Very Nice, My small airfoil/spilins now load's with .001, Conn.

line Toll. and Offset Properly, Nice and smooth.

Inside/Outside working Correct hear on this one now.

There are 4 that Did Offset before, But not now, See Below, Dxf Also.

The airfoils/splines were the bigest problem for Me.

Rapids for Arc's Don't change end's when moved.

Rapids for Lines Do change now, Maybe thy did before, Not sure.

Art, The "UN-Group" I Was talking about (Previous Yahoo Post), I think,

Would allow some of us to generate Lathe G-code.

Not trying to Un-group a Square/Closed Chain, Just a Line-Arc-Line Caine.

If you'd PM your PH #, I could probable better explain my thought's on this.

Any Way, Were Putting Together a Collection to Re-Attachl all that Pulled Out Hare, Save It,(;-}}.

Thank So-Much, Chip

1452

LazyCam (Beta) / Re: LazyCam 2.01.1

« on: July 10, 2007, 08:21:57 PM »

Hi, Brian

Yes, Add the .shp to upload files extents and I'll post some.

I think it just has to do with arc's, Circles seem fine.

Thanks, Chip

1453

LazyCam (Beta) / Re: LazyCam 2.081 Issues

« on: July 10, 2007, 08:11:23 PM »

Hi Paul

I see what you mean, It's a LCam internal issue I think Try going back a few versions May be better.

Hears what I got with LCam ver 2.01.0

Thanks, Chip

1454

General Mach Discussion / Re: Dohin Partmaster & Mach3

« on: July 10, 2007, 07:58:25 PM »

Hi, Bob

Sounds like your using LazyCam, If so click on the lead- in marker.

Then Double-Click it, A window will pop up, At the top set the lead-in to a smaller Value.

Hope this it It, Chip

1455

General Mach Discussion / Re: Mach3 and Boxford Duet

« on: July 10, 2007, 07:49:48 PM »

Hi, Piobaire

Looking at the data, There stepper motor driven, Check the stepper board/boxes for Info, Post it if you can.

There bound to be othe'rs hear that have some experience with them.

Just a Start, Chip

1456

LazyCam (Beta) / Re: LazyCam 2.081 Issues

« on: July 10, 2007, 03:13:46 PM »

Hi, Paul

Your Dxf loaded in BobCad 18 shows arc's backwards, Loaded it in TurboCad 8 shows correct, Saved it as new Dxf, Re-loaded in BobCad 18, Displays correct now.

All these Dxf's have different way's thy save info, So-many versions, The New Importer was supposted to handle many more, Guess thy Missed some.

The Dxf's have a header with Info it use's O-Well.

Try the one's bellow.

Hope this Helps, Chip

1457

LazyCam (Beta) / Re: LazyCam 2.080 Issues

« on: July 10, 2007, 01:56:24 AM »

Thanks, Brian

Chip

1458

LazyCam (Beta) / LazyCam 2.01.1

« on: July 10, 2007, 01:53:57 AM »

Hi, Art & Brian

After renaming the Extent from .1Exe to .Exe, LazyCam installed just fine  .

1.Shape files Save now  , But on load Shape File I get this below, Yellow shape  ,

The original shape is the light blue, The only way I could get it to hold this shape is with the left mouse button held down.

Let it up and it reverts to the yellow shape  .

Chip

1459

General Mach Discussion / Re: Update post from Art

« on: July 09, 2007, 11:41:15 PM »

Hi, Brian

the new LazyCam download is mis named as LazyCam2.01".1EXE", I renamed the exe and it seemed to load fine, OooPss.

Thanks, Chip

1460

LazyCam (Beta) / Re: LazyCam 2.081 Issues

« on: July 09, 2007, 11:14:47 PM »

Hi, Brian

Could you post a list of Default LCam Posts and a list of all commands used in posts for us.

The Zip file is all most one year old, You sed there are allot of additions.

Thanks, Chip