Hello Guest it is September 27, 2023, 10:59:57 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Chip

General Mach Discussion / Re: A axis movement
« on: July 22, 2007, 11:45:20 PM »
Hi, olf20

I think its the Bracket keys.

Hope this Helps, Chip

General Mach Discussion / Re: Pull-up Resistors
« on: July 22, 2007, 11:36:07 PM »
Hi, Ken

I think theres a description on the Rutex web site.

There tied to the A & B lines then to 5 volts TTL encoders, Around 470 ohm's, Hears the link to look at,

http://www.rutex.com/pdf/R9xHbdi.pdf   , page 7.

Hope this Helps, Chip

General Mach Discussion / Re: limit switch help
« on: July 21, 2007, 12:14:49 PM »
Hi, Mike

In Config, General Config, Set your De-bounce Interval to between  500 to 2000, Top Right of Screen.

If it's 0 now, This should help.

Thanks, Chip

General Mach Discussion / Re: DRO
« on: July 21, 2007, 11:51:19 AM »
Hi, Dhaxt

In Config, General Config..., Un-check the "Persistent DRO's" Box, Bottom Right of Screen.

That should fix it, Shut down Re- start Mach.

Hope this Helps, Chip

LazyCam (Beta) / Re: loading lazycam to mach3
« on: July 21, 2007, 11:31:52 AM »
Hi, Tashby

Maybe this is your problem ?

Brian Barker

There is a 50 line limit to Lcam if you are not a Licensed Mach3 user on that computer... We had to do this because we started to get users that were running the base version of Lcam and Not mach3! There is just no time to support a free product Sad If you have a licensed version of Lcam you are all set and you don't need to have a Mach3 license (There are people running Lcam to program other controls)

Also the Gcode limit of Mach3 is now 500 because there were machines being shipped with Demo version of mach3 and the OEM was telling them that there was a 1000 line limit to the control! O well...
Thanks, Chip

G-Code, CAD, and CAM discussions / Re: another sub-routine problem
« on: July 21, 2007, 08:18:50 AM »
Hi, Jimpinder

Check your second M99 has a Line feed or % sighn after it.


Hope this is It, Chip

General Mach Discussion / Re: Post processor
« on: July 20, 2007, 02:40:58 PM »
Hi, Rkjohn

Look under Offset's Tab, Bottom right, Save Tool Offset's, There are 254 counting tool 0, No secondary Offsets though.

Hope this Helps, Chip

General Mach Discussion / Re: Mach for turning
« on: July 20, 2007, 02:07:31 PM »
Hi Dennis

Hears the Mach3R 2.01.000 lock-down exe, Z is working in it properly.

Thanks, Chip

LazyCam (Beta) / Re: LazyCam 2.02
« on: July 13, 2007, 03:11:56 AM »
Hi, Art & Brian

Just some more.

Thanks, Chip

LazyCam (Beta) / Re: LazyCam 2.02
« on: July 13, 2007, 02:34:17 AM »
Hi, Art & Brian

The view Outside Offset, Wouldn't offset the top shape by it's self or with all selected.

Circle top offsets wrong.

Square doesn't offset top right corner

Inside Offset View, Circle off, Wouldn't offset the top shape by it's self or with all selected, Square Looks OK

Another example, Chip