Messages

1371

LazyCam (Beta) / Re: zero diameter circles and spurious circles

« on: October 27, 2007, 07:06:33 PM »

Hi, Lawrence

Post your lset file.

Hears one I made not proper font or size though, Using ver. 2.56.

I'll do a smaller one and try to find the other font time permitting.

Thanks, Chip

1372

General Mach Discussion / Re: New Mach3 install

« on: October 27, 2007, 06:44:55 PM »

Hi, Mark

The "Port 1 Pin's current State" don't flash, The "Blended Spd" , Current and Machine Coord should be moveing.

Check your Direction Pin's at Printer port for 0 or 5 volts depending on direction.

Thanks, Chip

1373

General Mach Discussion / Re: New Mach3 install

« on: October 26, 2007, 08:15:11 PM »

Hi, Markn

In your Mach3 folder you'll find a Driver Test Application, Click on it and let it run.

It will complete and close out, Then Re-Boot and run Mach3.

It's a Start, Chip

1374

General Mach Discussion / Re: mail

« on: October 26, 2007, 05:29:43 PM »

Hi, Orderit

Check your Email Junk folder, Thats where thy were for Me after the web site change over last week.

Select as Non Junk.

Hope this Helps, Chip

1375

General Mach Discussion / Re: Z Axis Move - Triggers Soft Limits

« on: October 25, 2007, 01:07:03 AM »

Hi, Denis

Could it be noise caused by the spindle starting, Tried it without spindle running.

Z binding at top.

Z Velocity or Acceleration set to fast.

Hope this Helps, Chip

1376

LazyCam (Beta) / Re: Limited to 50 lines

« on: October 24, 2007, 11:45:32 PM »

Hi, Ben

Licence.txt, Is just a text file not a license.

MachLic.data-file, Removes the 500 or 1000 line limit from Mach depending on version and turns on some other items, I don't have a list.

LazyLic.data-file, Removes the 50 line limit on later ver's of LazyCam and allows offseting, pocketing and turn features.

Don't now why it's working on one computer and not the other, there was some cross ups with ver numbers a while back.

Current ver are 2.56 for Both now.

Thanks, Chip

1377

General Mach Discussion / Re: Z axis going the oposite way it should.

« on: October 24, 2007, 09:33:48 PM »

Hi, mac102004

In Config, Home & Limits there is a Reversed Box for each Axis, Check it for your Z Axis.

Hope this Helps, Chip

1378

LazyCam (Beta) / Re: LazyCam 2.56 Arc Errors

« on: October 24, 2007, 09:24:57 PM »

Hi, Art

"(The extra rapids point though does go away if cleaned with a tolerance high enough.. )"

Are you talking about the setup load toll., tried .01 .001 .0001 .00001 , Zooming, Cleaning after moving start points.

Yes if you don't move any start points, the extra rapids aren't there.

Thanks, Chip

1379

LazyCam (Beta) / Re: Limited to 50 lines

« on: October 24, 2007, 06:44:25 PM »

Hi, Ben

It's working for me, Check for your LazyLic.data file in your Mach3 folder.

Chip

1380

LazyCam (Beta) / Re: LazyCam 2.56 Arc Errors

« on: October 24, 2007, 05:55:54 PM »

Hi, Art & Brian

With a Line connecting two of the arc's and Lset file

Thanks, Chip