Messages

1281

Video P*r*o*b*i*n*g / Re: MachCloud point viewer program

« on: November 28, 2007, 12:47:38 PM »

Hi, Art

Could you add the "X -1.0162 , Y  0.8038 , Z 4.7026", Format

That Mach can generate with Probing.

How dose the Decimate Cloud function work.

Thanks, Chip

1282

General Mach Discussion / Re: License install doesn't work

« on: November 28, 2007, 12:00:16 PM »

Hi, Dataceph

Try making a C:\Mach3 folder and put a copy of your Lic there, I Remember something on this in a Post some time back .

Hope this Helps, Chip

1283

General Mach Discussion / Re: Motors work with R2xtune but nothing with Mach!

« on: November 28, 2007, 11:39:09 AM »

Hi, Splint

Hear is a link to Rutex US thy have a diag for your 2120 board, http://www.rutex.com/us/home/index.htm

Have you disconnected the SPI jumpers used for tuning ?

Thy won't run Step/Dir, When in SPI Tune Mode. (Happen to Me 991 setup, Easy to miss).

In Mach3 Diagnostic page dose it show Pulse Frequency & Time in Int, Wtrh changing Values, Should Be changing.

Hope this Helps, Chip


You got it going, Great to hear, Chip

1284

General Mach Discussion / Re: Circles

« on: November 26, 2007, 08:18:33 PM »

Hi, Marco

Config, General Configuration, Change the "I,J Mode" State, Then Regen tool path should do it.

Thanks, Chip

1285

General Mach Discussion / Re: a- axis acts eratic HELP! PLEASE!

« on: November 26, 2007, 04:32:18 PM »

Hi, Glen

Look like you dropped through a Crack Hear, Sorry about that.

Have you swapped your Gecko's around.

What's your Power Supply Volt's Amp's,.

CPU speed, XP or 2000.

Looked at the Tutorials Above, Documentation, Optimize, There are programs like QuickTime that can cause Problems.

Are X and A set up exactly the same in, Ports & Pins, (step/Dir LowActives the same), Motor Tuning, (Steps Per, Vel & Accel), Home & Limits. ( Reversed un checked).

Thanks, Chip

1286

Video P*r*o*b*i*n*g / Re: MachCloud point viewer program

« on: November 25, 2007, 10:25:44 PM »

Hi, David

This is true Right click on file sel Properties then Change to notepad ect...

BobCad dose the same thing as do many other prog's when you install updates.

Thanks, Chip

1287

General Mach Discussion / Re: Re: printer cable pin connectiion

« on: November 25, 2007, 10:10:22 PM »

Hi, Dennis

Hears one http://www.doc.ic.ac.uk/~ih/doc/par/

Thanks, Chip

1288

General Mach Discussion / Re: Mach 3 on lap top wont operate

« on: November 25, 2007, 10:04:11 PM »

Hi, Al

Will it run a std. Printer ?

Thanks, Chip

1289

Video P*r*o*b*i*n*g / Re: MachCloud point viewer program

« on: November 25, 2007, 09:19:48 PM »

Hi, Art

Your Prop scanned some time ago looks pretty good in the Viewer.

Hears the file, http://www.machsupport.com/forum/index.php?action=dlattach;topic=1196.0;id=803

Thanks, Chip

1290

Video P*r*o*b*i*n*g / Re: MachCloud point viewer program

« on: November 25, 2007, 08:39:36 PM »

Hi, David

Yea but you have to do it every time you open a text file so it seems.

I'm sure it'll get sorted out soon, Some new . extent.

It's just nice to have viewer without all the CAD Work though.

Thanks, Chip