Hello Guest it is September 21, 2023, 12:10:21 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Chip

LazyCam (Beta) / Re: Layer-Chains out of sync
« on: January 02, 2008, 02:22:30 PM »
Hi, Bertho

It may be a bug, You can left click to high lite it, Then Rt-click and delete it on the left.

Chain's can be moved with a Rt-click also.

Hope this Helps, Chip

LazyCam (Beta) / Re: How do I order chains?
« on: January 02, 2008, 01:51:08 PM »
Hi, Bob

Well I call it a "RAT", It was bigger some time back, Just missing the ear's & nose and waggly tail, As far as I now there is no adjustment for speed.

As far as Documentation theres no real doc's yet, LC has been changing to fast, Just post's hear and at Yahoo group.

All these programs have led to affordable cnc control and with so many people sharing there talents, It's great

Learning More Every Day, Chip

General Mach Discussion / Re: Questions: M3Turn Tool Table
« on: January 02, 2008, 12:57:45 AM »
Hi, Overloaded

If your using LCam to generate your G-code, I think, Theres a Bug in the LC Default Post.

Thanks, Chip

LazyCam (Beta) / Re: How do I order chains?
« on: January 02, 2008, 12:44:40 AM »
Hi, Spinnetti

1. How do I order the chains?, I found how to select them individually, but not which direction or in which order. This is important because I have to cut a particular order out of the stock

Click on the first chain you want it will turn gray on the left side, Click on it on the left, Hold left mouse key down and drag it on top of chain0.

Chain0 will move down one, repeat this till you have the order you want. 

2. There is no stock definition? - would be nice to see what I'm cutting out of.

Best you can do is, Draw it in your DXF, Then delete it before posting.

3. There is no path simulation of the cut? - that would be nice too

Hit the "S" key to turn on the Rat, Hit the "S" key again to turn it off.

Hope this Helps, Chip

LazyCam (Beta) / Re: Insects
« on: January 02, 2008, 12:03:49 AM »
Hi, Bertho

I think these have all been reported, Theres still work to be done.

Brian may have a list.

Thanks, Chip

LazyCam (Beta) / Re: LazyCAM Beta- Pro installation
« on: January 01, 2008, 11:55:51 PM »
Hi, Bertho

I think you need to make a directory C:\Mach3 and put your license there, May need to copy LC there also.

Hope this Helps, Chip

General Mach Discussion / Re: Mach 3 controller not responding after?
« on: January 01, 2008, 11:12:58 PM »
Hi, Compositecrafters

Have you tried the "driver test" in C:\Mach3 folder, Let it run till it closes on it's own, Then re-boot and try Mach again.

You might need to remove "Mach3 Driver" in Device Manager, Right Click on it and Delete, then run the driver test again, It will re-install then run driver test as above one more time.

To get there Window's, Start, Control Panel, System, Hardware, Device Manager, Then MachX Pulsing Engines.

Hope this Helps, Chip

General Mach Discussion / Re: Wrong Arc
« on: January 01, 2008, 09:52:57 PM »
Hi, Aleks

Try drawing it in the upper left quadrant of your cad and set the post back to default setting.

Using BobCad V22 hear, Having some posting issues my self.

Try this DXF "top" and Txt " last" Download

Thanks, Chip

General Mach Discussion / Re: Wrong Arc
« on: January 01, 2008, 06:21:36 PM »
Hi, Aleks

What cad and post processor are you using ?

Could you post the DXF file

Thanks, Chip

Hi, Maxy

With "Ref. All", Z  ref's home first then Y then X, Is this what your getting ?