Hello Guest it is March 28, 2024, 06:02:47 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ardor

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »
41
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 03, 2007, 09:05:27 PM »
How disturbing it is to me to have to display the level of my ignorance. >:(  That sheet IS in my wiring diagrams.

Sending you a PM

Ashby

42
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 03, 2007, 06:38:44 PM »
That's what I get for posting info from what we laughingly call my memory.  The machine is only 50 ft. from the office.  Too lazy to go look. ::)

Ashby

So now I'm ready to whack a ribbon cable and connect an enable (1) from a pixie.  From the drawing, the odd numbers on the connector are on one row and the even on the other?

43
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 03, 2007, 03:08:53 PM »
Quote
Do your tools have a retension knob or threaded for a draw bar?

Retention knob.

That PDF that I posted for the PLC is a programming manual, no wiring details.  ........Rats.

Quote
The OUT. SVO-ON supplies ground directly to the relay of which the other side is connected to +24v (no PLC invovled.).

Where does the 24v come from.  The only 24v I see is from the power supply I took from the card cage.  24v on that isn't connected to anything yet.

Ashby

44
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 02, 2007, 04:38:55 PM »
Quote
If your spindle is single speed, I can't figure out what they used all the I/O for?

There was a read out of spdl speed on the console & I could bump the speed up or down from the console, maybe that's what a bunch of the I/O was about.

Is your PLC f1?.  I can't make it out on the pic.

45
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 02, 2007, 04:34:52 AM »
Here's pix of the PLC and Spindle Control.  The PDF manuals are to big to post here, so if you want to get them, I posted them
here-->>   http://wwbizz.com/Anilam/Darek

The PLC I have is F160MR, the only manual Mitsubishi had was for F2, they said that they were very similar.
The dwgs that I have don't show the I/O of the PLC.

Ashby

46
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: April 01, 2007, 12:55:11 PM »
I have removed the card cage and GXM Console.  Mounted the power supply from the card cage and have only run 5v from it to the BO board.  Have not connected any of the other outputs of that PS anywhere.

If the PLC needs info from P4, it's not connected to the card cage or the console anymore.

Are we working towards not using the PLC?

Ashby

47
Show"N"Tell ( Your Machines) / Re: My MPG remote
« on: April 01, 2007, 12:47:31 AM »
Hi...i have no plan to sell any ;)


Yet

48
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: March 31, 2007, 08:42:19 PM »

I planned on doing away with the PLC on mine and using basic Mach outputs.

Darek

I vote for that.  Is what I'm about to do with OUT. SVO-ON going to communicate with the PLC?  If so, then how to turn the drives on otherwise.

Ashby

49
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: March 31, 2007, 03:12:12 PM »
"You must have some kind of special spindle motor/drive combination to have power at low speeds."
The spindle motor is AC, the drive is a Yaskawa Varispeed 626MTIII

Can I tie the 3 enable lines of the Pixies together to connect to OUT. SVO-ON?  Would that help to sink the current?

Ashby

50
Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M
« on: March 31, 2007, 02:20:41 AM »
My breakout board is Accu-Step.  When I wired step/direction to Arturo's spindle control board I wired them to axis 4 on the BO board.  Couldn't see anywhere else, but it doesn't seem right.
Edit: After staring at the BO board for an hour or so, I figured that enabling axis A on motor tuning and setting step to 5 & dir to 9 on pport 1 should to the trick.

Also.
Quote
If you tie the error lines of the Pixies together, as suggested in the PDF, a fault on one axis will shut down all the Pixie's. This should allow the use one Pixie ENABLE output for OUT. SVO-ON.

you may need a driver transistor if the Pixie can not sink the relay current

Can I tie the 3 enable lines of the Pixies together to connect to OUT. SVO-ON?  Would that help to sink the current?

Ashby

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »