Hello Guest it is June 19, 2019, 01:41:35 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - giordano

Pages: « 1 2 3 4 5 6 »
31
General Mach Discussion / Re: Help for macro probe
« on: June 14, 2006, 07:56:30 AM »
Hi Brian. It doesn't import if the zero is made on the place or in a point specified in Tool Change Location. Aafter having planned the thickness of the probe, i would like the tool to automatically be lowered up to touch the probe (that is made with a microswith), to set zero the display and to place him in attended that Cycle Start is pressed. Does the example that you have written, do this? I have not had the time to try it, but I would need a complete macro because I am not competent of to write one of it. I am making a screenset, also simple, but in Italian. I don't succeed in understanding the operation of some buttons and therefore I don't know like to translate the labels. On the manual and on Wiki the indications are incomplete. Can you help? Thanks in advance, Giordano.

32
General Mach Discussion / Help for macro probe
« on: June 11, 2006, 01:34:42 PM »
I have seen the video of the macro that concerns the use of a probe, but I have not understood well as to write this program. My probe is top 55,23 mm. Can someone help to write the proper macro? Thanks in advance. Giordano

33
General Mach Discussion / Execution intermittent.....
« on: May 20, 2006, 06:37:55 PM »
Hi to all. I have used the files attached interpcnc.iso (pcb project) in Mach3. But the execution is not fluid but intermittent and the padses are not sometimes aligned. The option Constant velocity in the menu Config | State is selected. The same files executed with Ninos 3.1 it is perfect. I prefer to use Mach3. Do you have a remedy? Thanks in advance. Giordano

34
Hi. I have seen that in Screen4 there is a drop down box for the OEMs code that he/she takes the data from the files dros.txt. Is it possible to insert in Screen4 another drop down box? This can take the data from a files .txt like the language translations list. In this way it would be easier to create a simple interface in her own language. Thanks in advance. Giordano.

35
Hi. I would like to use the buttons and the standard labels of Mach3. In way any user can translate him/it in his/her own language. The bitmpaps are beautiful, but I think that it would be better to do first a standard interface, easier, on which every user could select  own language from a drop down box. Giordano

36
Hi to everybody. I am Italian. I would like to make the translation of the buttons and the labels used in Mach3. Is it possible to create of the buttons and of the labels with the text on two lines? Thanks in advance. Giordano

37
General Mach Discussion / Step per unit
« on: May 08, 2006, 07:46:11 AM »
Hi to all. I have read in a forum that the number in the playpen Step for unit it is critical. When Mach3  is installed this number is planned to 2000. I have a microstep controller RTA planned to 800 passi/giros and a screw with pitch 4mm. I have planned the number step for unit to 200. Is it correct? Thanks in advance. Giordano.

38
Mach Screens / Re: Screen simplified set
« on: May 03, 2006, 11:18:36 AM »
Thanks for the suggestions. Hi. Giordano

39
Mach Screens / Re: Screen simplified set
« on: May 02, 2006, 11:59:02 AM »
Hi Jeff. Thanks for the reply. I thought about using buttons and standard labels to the place of that sorts in JPG. Giordano.

40
Mach Screens / Screen simplified set
« on: April 27, 2006, 06:46:01 PM »
Hi to all. I am Italian. The screens shown sets are all very beautiful ones. Can an easier interface be created where the text of the buttons and the labels is gotten by a files of resource so that each can translate it in her own language? is it possible to use the VB script editor? Thanks. Giordano

Pages: « 1 2 3 4 5 6 »