Messages

11

General Mach Discussion / Re: What are the OEM Code of LEDs used in "Port 1 Pins current State"?

« on: June 25, 2009, 06:33:45 AM »

Hello, Chip. Making a new screenset Italian and wanted to monitor the activities of LPT1. Thank you. Giordano

12

General Mach Discussion / Re: What are the OEM Code of LEDs used in "Port 1 Pins current State"?

« on: June 24, 2009, 06:51:13 PM »

Hello Hood. Thanks for your reply. Let me explain better. For example, the LED pin 15 of LPT1 is OEM Code 140. Thank you.

13

General Mach Discussion / What are the OEM Code of LEDs used in "Port 1 Pins current State"?

« on: June 24, 2009, 06:39:01 PM »

Hello to all. Want to know the correspondence between the number of pins of LPT1 with the OEM Code (Led) 139 to 160. Thanks in advance. Giordano

14

General Mach Discussion / Led Set Variable Position

« on: May 27, 2009, 06:24:38 PM »

I would like to add a button led to Set Variable Position. The LED should turn on by pressing the button and turn off by pressing the button Goto Variable Position. Can you help? Thanks in advance. Giordano

15

General Mach Discussion / Re: Idea compensation planarità

« on: June 27, 2008, 02:51:31 PM »

Sorry .... sometimes the work plan is not perfectly linear. From x0 to xmax and y0 to ymax could be a small difference in height. It would be a good idea to make Mach3 setting these values be able to perform processing offsetting these differences. Hello Giordano.

16

General Mach Discussion / Idea compensation planarità

« on: June 27, 2008, 07:47:00 AM »

Hi to all. be a good idea, set zero the utensil in default points, to make to calculate to Mach3 a compensation of the planarità of the surface of support of the piece to work? excuse my English. Hi to everybody. Giordano

17

Works in progress / Idea for compensation of the planarità

« on: June 26, 2008, 06:26:24 PM »

Hi to all. be a good idea, set zero the utensil in default points, to make to calculate to Mach3 a compensation of the planarità of the surface of support of the piece to work? excuse my English. Hi to everybody. Giordano

18

General Mach Discussion / Re: problem with the modality Sherline

« on: January 28, 2008, 07:59:32 AM »

Hi Brian. I think about having resolved the problem installing the version 2.45 of Mach3 and an old file XML that I had saved. Also the mode Sherline correctly works. Perhaps the installation of the version 3.0 of Mach3 are not complete. Thanks for the help. Giordano

19

General Mach Discussion / mode Sherline doesn't work and a loss of step is had

« on: January 24, 2008, 08:20:16 AM »

I have replaced the old PC with a faster and the mode Sherline  doesn't work and a loss of step is had. Can I insert in step pulse and dir pulse a great value of 5 us to obviate to the problem directly? I use motor Sanyo and cards RTA planned to 800 step for turn. Do you think that I should reduce such value to 400 step for turn or secondary LPT to add a card to resolve the problem? Is there difference among a based PC on processor AMD and one on processor Intel?

20

General Mach Discussion / Re: problem with the modality Sherline

« on: January 23, 2008, 06:37:39 PM »

Hi. The LPT is planned well. If I disable the modality Sherline in the Ports and Pins page, the moves they are correct but with loss of step also returning to the version 2.5 of Mach3