Messages

11

Mach4 General Discussion / Re: Ethernet Smooth Stepper.

« on: December 16, 2014, 01:30:40 AM »

Hi All
Yuo are not going to beleive this but I just switched everything on and Hey Presto it all works
Thanks Bob

12

Mach4 General Discussion / Re: Ethernet Smooth Stepper.

« on: December 15, 2014, 02:25:34 AM »

Hi All
I hope someone can help.
I heve set up Mach 4 and ESS the same as mach 3 but when I jog X Y or Z the dro's move but the motors don't. When I jog A the DRO'S move and the motors move.
I am usung Win 7 32 bit with a C32 BOB my system works fine in Mach3.
Thanks
Bob

13

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 15, 2014, 02:29:03 AM »

Hi Art
so I could not get the m4 to keep its settings so I swopped computers and did a complete new install. And guess what everything is working beautiful.


Mach 4 V1936
Darwin 1.14.5

Thanks for all your help and hard work
Bob

14

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 14, 2014, 02:48:35 AM »

Hi Art
sorry to say I installed the latest  (1.12.a.1) and I still loose my settings . got to go to work now but will try a few things tonight and let you know
Bob

15

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 11:21:46 AM »

Hi Gerry
I also have nothing connected to mach4 ( I dont want to risk it)
but my fedd rate on running the arctest is stable at 97-98
bob

16

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 11:17:01 AM »

Hi Art
not to worry just resarted the PCand the errors have gone away .
I think there is a register that is not getting cleared properly and is causeing all sorts of problems.
If Brian wants any info I took some screen shots of my problems.
thanks
Bob

17

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 10:52:01 AM »

Hi Art
just resarted PC then Mach everything back to ruuning normal. I dont think this has anything to do with Darwin I think this is Mach.
Maybe Brian should get involved.
Bob

18

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 10:48:42 AM »

Hi Art
just lost all the motor enable settings in mach after a mach restart
Bob

19

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 10:45:34 AM »

Hi Art
I have deleted the old Darwin and loaded the new DLL and M4pw.
the first time I went to look at the settings of Darwin mach crashed needed a hard reboot.
since then I have restarted mach serveal time and all is OK I shall continue rebooting and restarting for the rest of the afternoon  (while watching Moto GP from Indianapolis )
and let you know what I find
Bob

20

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 09, 2014, 08:48:52 AM »

Hi Gerry  am going to try and find out how to close mach without a reboot.
But as everything is working now I dopnt want to play about with the settings .
bob