Hello Guest it is March 28, 2024, 12:40:50 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - uuccimi

Pages: 1 2 3 4 »
1
General Mach Discussion / Re: servo keep turning
« on: September 05, 2010, 01:02:38 PM »
I did try phase a into phase b & viceversa with the same results
[/quote]
Could it be your encoders are the wrong way round and you are getting run away?
Hood

2
General Mach Discussion / servo keep turning
« on: September 04, 2010, 09:40:38 PM »
my servos are hooked into a geckodriver g320 after I turn the power on the servos start running with stop, need help of how to fix this issue

3
Spanish / Re: Traducion del mach3 al español casi terminada.
« on: December 27, 2008, 07:36:47 PM »
Buenisiomo, de verdad que mucha persona les va a parecer muy util.

Solo tienes que escribir tus inquietues o preguntas al respecto, pues me gustaria colaborar de acuerdo a mis conocimientos
sobre todo con el VB - mas abajo habia ofrecido mi ayuda pero en realidad nadie contesto, es mas puedes contactarme por medio de "skype"
pues seria mas rapido, pues por medio de este medio no se si por ser un portal directamente en ingles, sobre todo en espanol que miro de vez en cuando
es muy lenta la respuesta

suerte


4
General Mach Discussion / post processor
« on: September 10, 2008, 11:46:59 PM »
Good place to learn all about post processor!

5
Spanish / Re: MACH en Español, MACH in Spanish
« on: August 29, 2008, 10:28:27 AM »
Buenos dias todos,

La propuesta de traducir completamente a espanol me parece buena idea y estoy dispuesto a colaborar con el Ingles, VB y otros conocimientos del mismo Mach, el detalle es el de hacer una cruzada bien aterrizada en cuanto ciertos modizmos que he visto en ciertos foros, los cuales deben de ser mas generalizados no regionalizados.
Tambien estoy seguro que a los creadores del Mach les intersara pues ellos mismos tienen la plataforma para desarrolladores la cual puede seer bajada de su portal.
Bueno me pueden mandar mensajes personales o nos podemos encontrar en "skype"
Suerte a todos!

6
VB and the development of wizards / VBScript to VB2005
« on: August 28, 2008, 12:15:59 PM »
Hi everyone!
VBScript that I want to change over to VB2005 code so I can make it an executable.  I know the code is similar, but there are a few differences and I am lacking VB2005 knowledge.  Also can someone tell me where can I learn to implement VB2005 code as Macro to Mach3?  I would greatly appreciate it!

7
General Mach Discussion / Re: BobCAM generating unusable g code...
« on: August 25, 2008, 02:18:40 PM »
Chip

Again... thanks for the help, but I need to figure out how to make this work for myself. I can't very well come to this or any other board with a jpeg of what I want and expect someone to write gcode for me. I need to understand what is going wrong.

chuff

...out there are many kinds of persons, and one of those many kinds: Ingrate and Thankfull.

Easy to forgived the UNTHANKFULL... but the INGRATES... N E V E R !

8
LazyCam (Beta) / Re: autocad vs. lazycam
« on: August 20, 2008, 12:46:43 PM »
Save as V12 .dxf from AutoCAD and try that.
Thanks ger21
V12.dxf  works!!!

9
LazyCam (Beta) / Re: autocad vs. lazycam
« on: August 20, 2008, 11:34:43 AM »
Did you close your dxf file that AutoCad created? If the file is still open, it won't load into LC.

Bob@BobsShop - Been there done that.
Ok, I did close autocad, try to open with Lcam, but won't load any thing and see 2749.87 scale number in the blue screen

10
LazyCam (Beta) / autocad vs. lazycam
« on: August 20, 2008, 10:23:38 AM »
How can open a DXF file onto LazyCam after was made out in Autocad
I did click OpenDXF in LazyCam but No Entities Found...

Pages: 1 2 3 4 »