Hello Guest it is March 28, 2024, 04:45:29 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Max Richards

Pages: 1
1
General Mach Discussion / Re: Help g codes
« on: February 19, 2015, 10:10:21 PM »
I see a massage, but it goes by so fast I can't read then nothing no codes.

2
General Mach Discussion / Help g codes
« on: February 19, 2015, 08:52:23 PM »
I have had my router for ten years and for the most part works fine. I had to reload mach3 with my disk. It will load, refhome,jog but will not load the g-codes I have installed it on 4 computers and it does the same thing. I have been on support with my machine teck and he is lost also, it seems to be a software problem to me. Can anyone help?

3
General Mach Discussion / Re: lossing home
« on: October 23, 2008, 07:53:47 PM »
I found the trouble.
I changed a belt the other day and got it way to tight.

Thanks to all for the help.

Max

4
General Mach Discussion / Re: lossing home
« on: October 23, 2008, 05:15:30 PM »
Yes I can see it when it stalls. I have checked the pulleys and they are tight. I took one motor lose and then the other it still happens even with one motor.  It happens after several lines have cut about line 58 to 66 everything is fine up to that time. I have tried different files and it happens. I cut a knife handle out fine with small cravings and it worked great,  but as soon as I went back to the large cuts (18inches) it started again.
It's  got  me stumped.

Max

5
General Mach Discussion / lossing home
« on: October 22, 2008, 07:34:48 PM »
Hi everyone,
I have a problem with with my ez-router machine it loses home when cutting. It will cut fine for a time then it loses home and will cut the next line several inches off. I have had the machine for two years and the files have cut great for a long time also I tried new files and still have the  problem. I can jog the machine on all axis with no trouble. It only
happens on the y axis. I have V-crave pro, 3dcut and vectorcut machinist and the problem is the same with all.

Thanks Max

6
General Mach Discussion / Re: buttons on mach3
« on: November 29, 2007, 11:52:06 AM »
I'll try. In my pictures flies the buttons that are used for the mach3 program are re patering themselves every few bays this is causing me to have duplicate files that is slowing my computer down. i have erased they but they keep coming back. I'm trying to find out why and how to stop this.

Max

7
General Mach Discussion / buttons on mach3
« on: November 28, 2007, 06:54:21 PM »
I have a problem with the button pictures copying over and over in my document files is this caused by mach 3 or is it caused by something else?

Thanks Max

8
General Mach Discussion / z axis is not working
« on: January 07, 2007, 05:19:47 PM »
ever time I set auto zero the router lowers touchs the plate then raises to hits the limit switch. I have to home ref and start over now the router its self will not turn on. It works five if I plug it in by itslelfs. I have unstall mach3 and installed agan. If anyone has a suggestion I'am all ears.

Max

9
General Mach Discussion / Re: roadrunner
« on: December 22, 2006, 10:06:35 PM »
I am new to this I have a ez-router and ran to the same thing when I first startred. I had to have my license to get past line 1000.

Max

Pages: 1