Messages

31

Works in progress / Re: Flash RU Screen

« on: May 17, 2010, 11:24:06 AM »

Hi Fabrice,

Sorry for the delay.
I store in DRO 2055 the offset of the first tool. The oneobtained when you measure using the "measure initial offset" button.
Here you have a list of the leds and dros I have defined so far.
I will see if I can implement the F5 funstion in the future.

Regards

32

Works in progress / Re: Flash RU Screen

« on: May 12, 2010, 11:03:01 AM »

Hi fabrice,
I installed led bars in my router gantry. The lamp button is for turning them on and off.
i will try to make that button customizable in the future. Right now it toggles output 6

Regarsd

33

Works in progress / Re: Flash RU Screen

« on: May 09, 2010, 12:27:57 PM »

Hi fabrice,

the auto zero bueeon and probe slider are actually for zeroing the part (maybe I used the wrong name)
I have a fixed zero touch plate installed in my machine, and I do manual tool change.

So when I put the first tool, I use the probe slider to zero it. When it is ready where i want it to be, I press the "initial tool offset" button and the tool travels to the fixed plate and measures.
Then each time I change a tool, I dont have to worry for the z zero. I just put it and press the auto zero button. The tool travels to the fixed plate and measures, and addapts the z zero according to the first tool.

1) Put first tool.
2) Set X,Y,Z manually or with the probe slider
3) Press the "initial tool measure" button to measure the tool against fixed plate
4) Run program
5) When toolchange is requested, change tool manually and press auto zero.

Hope that clarifies. I will correct the slider problem you reported

regards

34

Works in progress / Re: Flash RU Screen

« on: May 08, 2010, 05:53:48 PM »

New Version V1.34



1.34 Corrected a bug found by Fabrice Engel.
     when a wizard was posted, the values where taken from dros without being validated.
     This caused the screen to crash when the values had never been edited.
     
     I have added validation, but still some combination of values may lead to crash,
     specially when generating too many lines of code.

     Corrected graphic problem with depth in straight cut wizard and list of holes in holes wizard

35

Works in progress / Re: Flash RU Screen

« on: May 08, 2010, 11:42:46 AM »

Hi Fabrice,

I havent made the mdi screen yet. As soon as I have it i will share it

Regards

36

Works in progress / Re: Flash RU Screen

« on: May 07, 2010, 09:35:31 PM »

Hi Fabrice
The readrunner runs fine here. I use it all the time to test.

Can you please be more specific about the wizard problem so I can reproduce it?
Like what values you are entering, in wich wizard.
Also if possible opst your xml config file.

thanks

37

Works in progress / Re: Flash RU Screen

« on: May 07, 2010, 11:31:21 AM »

New update:


1.33 New and modified Macros: RefX,RefY,RefZ, M6Start, M1001

     Some corrections to the toolchange slider
     Correction to the bottom bar     
     
     Added Estimate time in the load screen

     Added diagnostics screen.
     Some leds can be changed by clicling on them or their label


     Added optional stop feature.
     To make an optional stop code must have 2 consucutive lines:
   M1001
        M01
     Could not do it through M01 alone because theres no optional stop led for it.

     Added rapids override button on feed override slider.
     I may change its location in the future because it does not work while part is running

There may be new bugs. Please report them
thanks

38

Works in progress / Re: Flash RU Screen

« on: May 06, 2010, 02:30:40 PM »

Hi Fabrice,

Some buttons, as the Start button, that when unintentionally pressed may lead to a crash or accident, are protected by a safety timer.
You have to keep the button pressed for the specified time. If you release it before, the event will not trigger.

The default time value for the Start button is 500ms , and when in step mode 200ms.
You can change that to the value you preffer in the RUCONFIG.INI file.

regards

PD: The screen aspect is designed for 1280x1024 resolution

39

Works in progress / Re: Flash RU Screen

« on: May 06, 2010, 02:27:20 PM »

Hi Fabrice,

Some buttons, as the Start button, that when unintentionally pressed may lead to a crash or accident, are protected by a safety timer.
You have to keep the button pressed for the specified time. If you release it before, the event will not trigger.

The default time value for the Start button is 500ms , and when in step mode 200ms.
You can change that to the value you preffer in the RUCONFIG.INI file.

regards

PD: The screen aspect is designed for 1280x1024 screen resolution

40

Works in progress / Re: Flash RU Screen

« on: May 05, 2010, 09:33:33 PM »

In order to view the screen properly, please download and install this fonts into your system.

Thanks