Hello Guest it is March 02, 2021, 04:05:05 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DMBGO

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 »
151
General Mach Discussion / Re: Servo Motor question
« on: March 11, 2011, 01:59:09 AM »
I have pretty well decided to go with the VM760 machine frame below. I wont be buying the servos vfd or spindle from the manufacturer, since I think I can do better elsewhere. They have been pretty good to deal with so far, they are happy to provide couplers and make the motor mounts etc to suit the servos and spindle motor that I choose.

152
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 05:12:35 PM »
Well there could be worms in the castings!!

153
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 05:03:39 PM »
This is to import the machine from Taiwan, so there will be another $3000.00 in freight and port charges etc.

154
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 05:02:32 PM »
Base machine FRAME   $12,992.00
BT40 spindle speed 10000rpm extra   $179.00
4. Armless(Genoa) type 10 tools ATC       $1,456.00
10. Spindle motor 7.5hp (10000rpm, inverter motor   $1,064.00
12. Inverter driver 7.5hp/220V (VFD055V23A-2/Delta   $1,064.00
15. X,Y,Z with brake AC servo motor 220V/1kw   $980.00
18. Oil mist lubrication pump   $448.00
23. Remote handwheel   $280.00
Fumigation fee   $100.00
24. Limit switches (3 pcs)   $252.00
25. Interlock switch for front door   $224.00
26. Air gun   $34.00
27. Coolant gun   $34.00
20. Heat exchanger for electrical box   $134.00
21. Electrical fan for electrical box (1pcs)   $22.00

155
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 04:15:57 PM »
The VM760 is what I am leaning towards too, It is quite modular in that you can buy anything from the base machine without motors ATC etc upwards.

156
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 05:55:10 AM »
I intend to use the smoothstepper with it, here's the machine btw

I'm also looking at the VM760

Any comments would be appreciated


Cheers
Dave


157
General Mach Discussion / Re: Servo Motor question
« on: March 01, 2011, 04:40:21 AM »
Thanks for that Hood, It's been a while! Sorry for being lazy and asking, I should have done my homework, but I needed to get back to the guy quickly.

Thanks again

Dave

158
General Mach Discussion / Servo Motor question
« on: March 01, 2011, 03:19:28 AM »
Hi I am looking at buying a mill which is already a cnc mill, it had the option of a built in Chinese CNC controller, but I asked them to quote the mill with just the servos and drives.

The Servos are AC servos, and I am wondering if there would be any difficulty interfacing them with Mach3.
Here is a link to the manual for the servo drives

http://www.gskcnc.com/Support/DA98A_ACDriver.pdf

I have had a lot of experience in the past with steppers, but servos are a whole new ball game to me.

Thanks
Dave

159
Finished Plugins for Download / Re: Huanyang VFD controller plugin
« on: February 23, 2011, 06:11:07 PM »
I have about 6 versions of this manual, most are missing the last section with the diagnostic error codes, this one is the most recent, and is the only one that is actually from Huanyang
Cheers
Dave M

160
Finished Plugins for Download / Re: Huanyang VFD controller plugin
« on: February 23, 2011, 04:54:31 PM »
There is a quite recent version  of the manual here: http://www.jinlantrade.com/ebay/invertermanual.pdf

Regards
Dave M

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 »