Messages

51

General Mach Discussion / Re: USB Camera connection

« on: August 21, 2018, 07:57:51 AM »

The message "OSG driver" is definitly not coming from my plugin.
is this message appearing every time you start the plugin?
Did you install a deticated driver for the camera?
Did you try the camera on a different USB port?

The only requirements for connecting to a camera:

The defautl Mach3 plugin "Video Window" must not be started since the last windows start
The camera must be plugged in before the plugin is started

Klaus

52

General Mach Discussion / Re: USB Camera connection

« on: August 21, 2018, 06:07:50 AM »

What type of camera are you using. Is it an USB connected camera?

Klaus

53

General Mach Discussion / Re: USB Camera connection

« on: August 20, 2018, 04:13:43 PM »

Hi,

which plugin are you using?

Klaus

54

Machscreen Screen Designer / Re: MachScreen releases

« on: May 16, 2018, 03:08:34 AM »

Hi,
for general description a good place is Mach3Wiki      http://www.machsupport.com/Mach3Wiki/index.php?title=Main_Page
another good place is                                            http://www.machsupport.com/help-learning/product-manuals/
on my site "Mach3ScreenDesigner"                          http://www.kd-dietz.com/klausphp/index_eng.html
you'll find tutorials and videos

Klaus

55

Machscreen Screen Designer / Re: MachScreen releases

« on: May 15, 2018, 04:12:47 AM »

Hi Esteb

did you swap the layer using the context menu(right button)? If so, try the following:
make sure multi-selection is on (second icon from the right of the toolbar) showing "M"
hit the spot where all of your controls overlap. A list pops up with the overlaying controls
when hovering over the "Control element" column, the corrisponding element frame is highlighted
select the element and drag it to the display level you want (drag and drop).

If that doesn't work, perhaps you could send me your screenset for further investigation.

Klaus

56

General Mach Discussion / Re: X Y axis move togehter with Arrows key

« on: March 01, 2018, 04:27:11 PM »

Hi Roger,

I also don't have a pendant. Try the following:
Ports and Pins -> Input Signals
Jog X++    Enabled Emulated Hotkey 38 (arrow up)
Jog X--      Enabled Emulated Hotkey 40 (arrow down)
Jog Y++    Enabled Emulated Hotkey 39 (arrow right)
Jog Y--      Enabled Emulated Hotkey 37 (arrow left)

Apply
Reset
occasionally I had to change the Jog mode with the fly out dialog
Jogging with the arrow keys up, down, left or riight show x and y movement on the DRO's

Klaus

57

General Mach Discussion / Re: X Y axis move togehter with Arrows key

« on: March 01, 2018, 03:58:40 PM »

Hi

I don't think so. You can test it with the standard screen 1024.set. Just change the settings, in the "Port Setup and Axis Selection". I tested on Win10 Mach3 V3.043.062 without a parallel port and could see the x and y movement on the DRO's.

Klaus

58

General Mach Discussion / Re: X Y axis move togehter with Arrows key

« on: March 01, 2018, 06:32:27 AM »

Yes, but only if "Emulated" is also checked.


Klaus

59

General Mach Discussion / Re: X Y axis move togehter with Arrows key

« on: March 01, 2018, 06:08:59 AM »

Hi Roger

you're rigth. But the profiles I got were opposite. Keys up / down were 39 37 which is x-direction.

Klaus

60

General Mach Discussion / Re: X Y axis move togehter with Arrows key

« on: March 01, 2018, 05:30:18 AM »

Hi Roger

this explanation regards the dialog "Port Setup and Axis selection Input signals"

this problem occurs if Emulated is checked and the Hotkey settings are mixed up in x and y direction.

to correct this, change
JogX++ to 39
JogX--   to 37
JogY++ to 38
JogY--   to 40

or uncheck the "Emulated" button.


Klaus