Hello Guest it is June 26, 2019, 07:10:41 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - inivator

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »
91
General Mach Discussion / Re: Limit Switch Problems
« on: June 19, 2008, 05:29:52 PM »
I have done what you said. I have discovered that with all the axis homes enabled, I can reset.  As soon a I enable anything else, I can not reset, even with the limit switches disconnected.

Inivator

92
General Mach Discussion / Re: Limit Switch Problems
« on: June 19, 2008, 04:00:53 PM »
I did as you said, but now I can't reset the E Stop from the screen.  There is no physical E Stop switch.

Dumb as usual...........

Inivator

93
General Mach Discussion / Limit Switch Problems
« on: June 19, 2008, 03:43:58 PM »
I have wired all of the limit switches in series, X,Y,Z, checked them with Ohm meter, readings are as they should be, wired to breakout board Grnd. to Grnd., the other to pin 12.  How do I set up the pins and ports on the software for them to work.

Inivator

94
General Mach Discussion / Re: wiring diagram for limit switches
« on: June 16, 2008, 01:05:28 PM »
Hood;

When you're ready to take a vacation, come to TEXAS, and I will show you how red-necks live.................I've been here 70 years, and have just about figured it out, whatever it is............

Inivator

95
General Mach Discussion / Re: wiring diagram for limit switches
« on: June 16, 2008, 08:20:52 AM »
Thanks...Sounds simple, very similiar to my mind...........

Inivator

96
General Mach Discussion / Re: wiring diagram for limit switches
« on: June 16, 2008, 07:36:16 AM »
Understand the wiring now, but how is the configuration in the Mach3 software setup?

Inivator

97
General Mach Discussion / wiring diagram for limit switches
« on: June 15, 2008, 04:29:54 PM »
I'm building a gantry type small router.  Is there any wiring diagrams for simple xyz limits and homing switches.

Inivator ???

98
General Mach Discussion / Re: NO POWER
« on: June 14, 2008, 02:15:45 PM »
No LED on board for direction change.  Will check the voltage drop..........

Thanks

99
General Mach Discussion / Re: NO POWER
« on: June 14, 2008, 01:51:13 PM »
Yes, they were working before limits set-up.
Trying to move from keyboard.  Dro's move, but not the motors.
Have not tried MDI command yet.
Have disabledports and pins.

thanks for the quick reply.....Inivator

100
General Mach Discussion / NO POWER
« on: June 14, 2008, 01:05:27 PM »
I just started setting up my machine after rewiring for limits, and now I can't get the motors to move.  I am using Probotix 3 axis system, all of the board lights come on normal, have checked the power outputs as described, but the motors will not move.  I tried hooking up one motor at a time, using the last motor tuning info. , which was working, but now the motors work move.  I have even un-wired the input wires to the limits, but still motors do not move.  What do I check Now..........

Hepl please............

Inivator


Pages: « 1 2 3 4 5 6 7 8 9 10 11 »