Hello Guest it is November 22, 2019, 04:44:40 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - inivator

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »
31
General Mach Discussion / Re: ROUTER STOPPING DURING PROGRAM RUN
« on: August 02, 2008, 01:21:31 PM »
NOT USING SHEILDED WIRE.  WILL INCREASE THE DEBOUNCE, AND SEE IT THAT HELPS.

THANKS FOR THE INFO AND HELP

INIVATOR

32
General Mach Discussion / Re: ROUTER STOPPING DURING PROGRAM RUN
« on: August 02, 2008, 01:06:35 PM »
NO JIM, THE MACHINE JUST QUITS OR DIES, AND THE RESET BUTTON IS ACTIVATED, BUT IT HITS NO LIMITS SWITCHES...  I CAN RESET, AND REHOME, AND START THE MACHINE AGAIN, IT WILL EVENTUALLY STOP, NOT ALWAYS IN THE SAME PLACE OF SAME DEPTH..

INIVATOR

33
General Mach Discussion / Re: ROUTER STOPPING DURING PROGRAM RUN
« on: August 02, 2008, 12:52:43 PM »
I ALSO NOTICE THAT THE MACHINES STOPS FOR A MILISECOND AND THE START OF THE ARCS, THE RUNS FOR A SHORT TIME, THEN COMPLETELY STOPS.
THE ROUTER CONTINUES TO RUN.

INIVATOR

34
General Mach Discussion / Re: ROUTER STOPPING DURING PROGRAM RUN
« on: August 02, 2008, 12:48:21 PM »
NO THE MACHINE STOPS. 

INIVATOR

35
General Mach Discussion / ROUTER STOPPING DURING PROGRAM RUN
« on: August 02, 2008, 11:57:35 AM »
RUNNIG THE ATTACHED PROGRAM USING A 1/16" CARBIDE , THE ROUTER WILL STOP COMPLETELY.  PRIOR TO STOPPING I NOTICE THE HESITATION AT THE END OR BEGINNING OF THE ARCS.  IT GENERALLY HAPPENS ABOUT THE THIRD OR FORTH PASS.

I NEED SO DIRECTION.............PLEASE

INIVATOR

36
General Mach Discussion / SUB-ROUTINE PROBLEMS
« on: July 31, 2008, 10:45:30 AM »
I TRIED TO RUN THIS, BUT THE MACHINE DOES NOTHING.  WHAT DO I NEED TO DO???????????????

INIVATOR

37
General Mach Discussion / Re: Losing position on all axis
« on: July 28, 2008, 09:29:22 AM »
Will try that. Thanks.

Inivator

38
General Mach Discussion / Re: Losing position on all axis
« on: July 28, 2008, 09:17:06 AM »
The breakout is the same.  I had to change it because the limit switch chip was bad.  Probotix change the board, and the limits are working fine.  Now the repetivative move are not the same.  This is the problem, I stated yesterday, in the abnormal ref-all post. 

Inivator

39
General Mach Discussion / Losing position on all axis
« on: July 28, 2008, 08:41:13 AM »
 >:(Thing were working fine, but I had to change my P.port Breakout board from Probotix, now I am losing position in a negative direction, meaning x and y distances are getting smaller.  Do I have to re-tune the motors and change the math on the leadscrews????????????????

Inivator

40
General Mach Discussion / Re: Abnornal Refall Light
« on: July 27, 2008, 07:51:36 PM »
I'LL TRY THAT...THANKS.  I WON'T BE DOING ANYTHING ELSE TODAY, THE BOSS-LADY SAYS IT IS HONEY-DO TIME.

AGAIN THANKS ;D ;D ;D
INIVATOR

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »