Messages

1

General Mach Discussion / Re: G Code Causing Problem with Plasma Machine

« on: April 01, 2009, 12:18:46 PM »

i have had the same problem before. are you using lazycam? i create toolpaths in turbocad. i found that i have to explode all arcs and then  join polylines to get rid of that. for some reason lazycam would insert extra m3 m5 commands if left as lines and arcs. another thing could be tiny pionts left on a drawing. lazycam will create a m3 m5 for those.

2

General Mach Discussion / Re: Servo with Gecko320 blowing fuses

« on: March 25, 2009, 11:59:25 AM »

what size fuse are you using? the gecko 320 is rated 20 amps.

3

Finished Screens / Re: Mach SoftLight

« on: January 11, 2008, 09:03:31 AM »

nice screen! 
the extra tab at the bottom for jogging is great.  when i use the buttons for jogging, i get no movement. the mpg works . do i have to select a hotkey for this?


thanks

4

General Mach Discussion / Re: Breakout Boards

« on: November 17, 2007, 07:56:33 PM »

hi, i am connected thru 2 pci parrallel port cards.one is being used for outputs to larken viper drives and manual pulse generator. . the other pci port is connected thru a sound logic breakout board which has safety charge pump and onboard relays . works for me.the onboard parallel port on the motherboard i have disabled.if your drive has isolation already, why  add another buffer between them?

5

General Mach Discussion / Re: Breakout Boards

« on: November 17, 2007, 06:04:11 PM »

i agree, breakout boards have given me endless hours of troubleshooting to remedy lost steps.i use 1 but only for inputs and relay outputs.a heads up on an ebay seller wilhelmjason.a dispute this guy resulted in him threatening to target me with his hacker forums to spam the crap out of me.real creep.

6

General Mach Discussion / Re: Boss 9 retrofit querry

« on: August 24, 2007, 09:43:03 AM »

hi, did not have any problemswith vibrations.i have since sold this machine and the current owner is very pleased with its performance.i have another almost complete, sajo cnc vertical  mill,using larken viper drives.

7

General Mach Discussion / X, Y & Z changes when I reset or go into options

« on: July 18, 2007, 01:12:15 PM »

I just got my CNC running on Monday with Mach 3 software, so I am a newb with this piece of software.  But if I click on the x y & z to reset them to 0, and then go into one of the options menus... even if I don't change a single option, the x y & z change to seemingly random numbers like the 0.000 will change to say 8.6293.  What is with that?   It seems to happen by pressing the reset button as well.


Thanks

8

General Mach Discussion / Re: setting up second parallel port

« on: July 11, 2007, 09:36:44 AM »

corydoras, sorry cant help. sold that machine. a suggestion though. have you tried reinstalling the driver from the cd that came with the pport?

9

General Mach Discussion / Re: Trying to get 2nd parallel port card working, need help!

« on: June 14, 2007, 02:43:23 PM »

have you rebooted?
i just went thru this not with a netmos but another brand sunex  . after entering the address, it worked fine. have you checked the diagnostics , try setting the pins for an input of a limit switch, or an mpg. if the port is working you will see the leds lighting up.

10

General Mach Discussion / Re: mpg and mach 3

« on: March 24, 2007, 10:09:50 AM »

installed the caps on the ipac, no problems. ran the roadrunner  file  10 times with no estop tripping.