Hello Guest it is September 28, 2021, 12:06:45 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TDAY

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »
121
Newfangled Solutions Mach3 Wizards / Re: ODD Comp Move
« on: June 05, 2009, 09:35:12 AM »
After more testing.....

To get problem to repeat i do the following...
1)Start Mach3 & Reference each axis starting with Z,Y,X
2)Make or open Gcode File.
3) Zero X and Y on part and Set Tool Offset

If i leave the Zero of X and Y at th Referance position, there is no problem, but if i move the X and Y and Zero, then  comp move makes machine run off at full rapid in a big arc move.
After this i get a message when i try to rerun program.  "Current point same as end point of arcLine 33"   I then must restart Mach to get programs to run right.When i do a Regen. Toolpath after i move zero of part from the Ref. postition, then there is no problems.

On another test i did the following ......
1)Start Mach3,Reference each axis starting with Z,Y,X
2)Zero Xand Y on part,then Set Tool Offset
3) Make or open Gcode.

When i do this the Odd Comp move does not happen(at least not yet).
Troy

122
Newfangled Solutions Mach3 Wizards / Re: ODD Comp Move
« on: June 05, 2009, 08:17:57 AM »
Done some more testing almost getting a steady repetition of odd comp move, using the below, unedited Gcode.

(Code by Newfangled Wizard, 6/5/2009)
(Version 2.83)
(Program Posted for Medium Steel )
G0 G49 G40.1 G17
G80 G50 G90 G98 
G20 (Inch)
(***** Circular Groove/Cutout *****)
M6 T2
M03 S573
M9
G00G43 H2 Z0.1
G00 X-0.465 Y-0.375
G41 P0.25
G01 X-0.09 F10
G03 X0.285 Y0 R0.375 F10
F10
G03 X-0.285 Y0 R0.285 Z-0.015
X0.285 Y0 R0.285 Z-0.03
X-0.285 Y0 R0.285 Z-0.045
X0.285 Y0 R0.285 Z-0.06
X-0.285 Y0 R0.285 Z-0.075
X0.285 Y0 R0.285 Z-0.09
X-0.285 Y0 R0.285 Z-0.105
X0.285 Y0 R0.285 Z-0.12
X-0.285 Y0 R0.285 Z-0.135
X0.285 Y0 R0.285 Z-0.15
X-0.285 Y0 R0.285 Z-0.165
X0.285 Y0 R0.285 Z-0.18
X-0.285 Y0 R0.285 Z-0.18375
X0.285 Y0 R0.285 Z-0.1875
X-0.285 Y0 R0.285
X0.285 Y0 R0.285
G00 Z0.1
G03 X-0.09 Y0.375 R0.375
G40
G00 X-0.465 Y0.375
M5 M9
M30
 

123
Newfangled Solutions Mach3 Wizards / Re: ODD Comp Move
« on: June 05, 2009, 08:00:45 AM »
I added the drill cycle, the M6 tool change cancels the Canned Cycle, as for simple example, the odd comp move would happen at the first Circular Groove/Cutout. But, as i said before, the Odd Comp move does not happen all the time. I cant get it to repeat  ??? .  When it happens it only does it once, and then i stop and reset the Gcode, and start again,and there is no probs.
Thanks,
Troy

124
Newfangled Solutions Mach3 Wizards / Re: ODD Comp Move
« on: June 05, 2009, 06:40:35 AM »
Here is the program i was using.

(Code by Newfangled Wizard, 5/27/2009)
(Version 2.83)
(Program Posted for Medium Steel )
G0 G49 G40.1 G17
G80 G50 G90 G98 
G20 (Inch)
(***** Circular Groove/Cutout *****)
M6T1
M8
G83X11.6875Y0R.1Z-.5Q.05
X10.5
X9.3125
M9
M6 T2
M03 S573
M8
G00 X11.2225 Y-0.375
Z.1
G41
G01 X11.5975 F10
G03 X11.9725 Y0 R0.375 F10
F10
G03 X11.4025 Y0 R0.285 Z-0.015
X11.9725 Y0 R0.285 Z-0.03
X11.4025 Y0 R0.285 Z-0.045
X11.9725 Y0 R0.285 Z-0.06
X11.4025 Y0 R0.285 Z-0.075
X11.9725 Y0 R0.285 Z-0.09
X11.4025 Y0 R0.285 Z-0.105
X11.9725 Y0 R0.285 Z-0.12
X11.4025 Y0 R0.285 Z-0.135
X11.9725 Y0 R0.285 Z-0.15
X11.4025 Y0 R0.285 Z-0.165
X11.9725 Y0 R0.285 Z-0.18
X11.4025 Y0 R0.285 Z-0.18375
X11.9725 Y0 R0.285 Z-0.1875
X11.4025 Y0 R0.285
X11.9725 Y0 R0.285
G00 Z0.1
G03 X11.5975 Y0.375 R0.375
G40
G00 X11.2225 Y0.375
(***** Circular Groove/Cutout *****)
G00 Z0.1
G00 X10.035 Y-0.375
G41
G01 X10.41 F10
G03 X10.785 Y0 R0.375 F10
F10
G03 X10.215 Y0 R0.285 Z-0.015
X10.785 Y0 R0.285 Z-0.03
X10.215 Y0 R0.285 Z-0.045
X10.785 Y0 R0.285 Z-0.06
X10.215 Y0 R0.285 Z-0.075
X10.785 Y0 R0.285 Z-0.09
X10.215 Y0 R0.285 Z-0.105
X10.785 Y0 R0.285 Z-0.12
X10.215 Y0 R0.285 Z-0.135
X10.785 Y0 R0.285 Z-0.15
X10.215 Y0 R0.285 Z-0.165
X10.785 Y0 R0.285 Z-0.18
X10.215 Y0 R0.285 Z-0.18375
X10.785 Y0 R0.285 Z-0.1875
X10.215 Y0 R0.285
X10.785 Y0 R0.285
G00 Z0.1
G03 X10.41 Y0.375 R0.375
G40
G00 X10.035 Y0.375
(***** Circular Groove/Cutout *****)
G00 Z0.1
G00 X8.8475 Y-0.375
G41
G01 X9.2225 F10
G03 X9.5975 Y0 R0.375 F10
F10
G03 X9.0275 Y0 R0.285 Z-0.015
X9.5975 Y0 R0.285 Z-0.03
X9.0275 Y0 R0.285 Z-0.045
X9.5975 Y0 R0.285 Z-0.06
X9.0275 Y0 R0.285 Z-0.075
X9.5975 Y0 R0.285 Z-0.09
X9.0275 Y0 R0.285 Z-0.105
X9.5975 Y0 R0.285 Z-0.12
X9.0275 Y0 R0.285 Z-0.135
X9.5975 Y0 R0.285 Z-0.15
X9.0275 Y0 R0.285 Z-0.165
X9.5975 Y0 R0.285 Z-0.18
X9.0275 Y0 R0.285 Z-0.18375
X9.5975 Y0 R0.285 Z-0.1875
X9.0275 Y0 R0.285
X9.5975 Y0 R0.285
G00 Z0.1
G03 X9.2225 Y0.375 R0.375
G40
G00 X8.8475 Y0.375
M5 M9
G28
M30

125
Newfangled Solutions Mach3 Wizards / ODD Comp Move
« on: May 27, 2009, 08:32:36 AM »
Has anyone had a ODD cutter comp move with Cut Circle,or somthin else?
After making program and returning to Mach the Toolpath shows wright. But upon 1ST run of program, comp move is fast and WAY out of diameter of circle.When i stop and reset program, the next run works fine.Cant get this to happen every time thow. Almost "seems" like if it is the 1st comp move of the day, is when it does it.
Any Ideas?
Troy

126
Newfangled Solutions Mach3 Wizards / Re: 2.83 ready
« on: April 29, 2009, 08:54:54 AM »
Hello,
 A while back Cutter Comp for Threadmill was brought up.Is it still in the works?
Thanks,
Troy

127
Newfangled Solutions Mach3 Wizards / "Graphics" run in preview
« on: January 30, 2009, 10:28:14 AM »
Hello Ron,
 Wondering if a graphics or Dry Run can be added to the preview of wizards? So one can watch program run in the Preview,before posting Gcode, as this would help much if a program has a few wizards. Also it would run offline and NOT move the actual machine.
Thanks,
Troy

128
Newfangled Solutions Mach3 Wizards / Re: Rectangle do a oval?
« on: January 06, 2009, 04:07:14 PM »
Nice idea,but would be time consuming to run part.I would rather do the Gcoding with Cutter Comp.
I thought the Rectangle wizard could do it,as i have ran other CNCs that had a similar "wizard" that would do oval shapes also.
Thanks,
Troy

129
Newfangled Solutions Mach3 Wizards / Re: Rectangle do a oval?
« on: January 06, 2009, 02:44:21 PM »
Ya,but i was doing a outside shape.And i need to be able to change the size of the oval.
Thanks,
Troy

130
Newfangled Solutions Mach3 Wizards / Re: Request for New Wizard
« on: January 06, 2009, 08:13:00 AM »
Brian,
 Is this still in the works? Your point to point wizard idea sounds awesome.Along with a multi-pass or roughing sequence like the pocketing wizards.
Troy

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »