Hello Guest it is May 09, 2021, 09:31:30 AM
Profile Guest

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jlautomatio

Pages: « 1 2 3 4 5 »
31
LazyCam (Beta) / Re: lazycam
« on: July 01, 2006, 10:43:42 AM »
Hi Brian
did you find solution for the dot  the reason it making 2 time the hole
thank you

32
LazyCam (Beta) / Re: How to download Lazy Cam
« on: July 01, 2006, 08:44:21 AM »
to get laycam you have to download mach 3 1.90.060

33
LazyCam (Beta) / Re: lazycam
« on: June 28, 2006, 08:35:20 PM »
well done
good work
one think funny

check line n8 z go down
n9 go up
n10 go down again

it make the hole 2 times
same think 21 22 23

1 (File cut22 )
N2 (File Posted in Mill Mode)
N3 (Wednesday, June 28, 2006)
N4 G90G40G80G94 G91.1
N5 G0 Z10.0000
N6    X37.0742 Y19.0897
N7 M3
N8 G1 Z0.0000  F300.00
N9 G0 G98 Z10.0000
N10 G81 X37.0742 Y19.0897 Z0.0000 R10.0000 F500.00
N11 G80
N12 G0 X189.7125 Y25.6922
N13 G1 Z0.0000  F300.00
N14    Y74.2922  F500.00
N15 G3 X170.6625 Y93.3422 I-19.0500 J0.0000
N16 G1 X67.4625
N17 G3 X48.4125 Y74.2922 I-0.0000 J-19.0500
N18 G1 Y25.6922
N19 G0 Z10.0000
N20    X203.8787 Y21.1578
N21 G1 Z0.0000  F300.00
N22  G98 Z10.0000
N23 G81 X203.8787 Y21.1578 Z0.0000 R10.0000 F500.00
N24 G80
N25 G0 Z10.0000
N26 M5 M9
N27 X0.0 Y0.0
N28 G40M30G80

34
LazyCam (Beta) / Re: lazycam
« on: June 28, 2006, 08:02:25 PM »
if it fix send to me
thank you

35
LazyCam (Beta) / Re: lazycam
« on: June 28, 2006, 04:31:03 PM »
ok now it working i put in pre-amble to code output
G94 an it change the mode on mach3 this is ok

one more think
if i load dxf file and keep layer info. it work ok but i have to enter all the info for layer control
like feed plunger hight  ext. take time to enter

if i load dxf and ignore layer inf. the layer control all the info are there if i put outside off
in the inside if i have dot it show the dot and if i generate the gcode all the dot it say Radius to end of arc differ from radius to start on line number #17

N1 (File cut22 )
N2 (File Posted in Mill Mode)
N3 (Wednesday, June 28, 2006)
N4 G90G80G40G94 G90.1
N5 G0 Z10.0000
N6    X37.0742 Y19.0897
N7 M3
N8    Z9.5000
N9 G1 Z0.0000  F300.00
N10 G0G98 Z10.0000
N11 G81 X37.0742 Y19.0897 Z0.0000 R10.0000 F500.00
N12 G0 X197.8373 Y25.6922
N13    Z9.5000
N14 G1 Z0.0000  F300.00
N15 G80
N16    X189.7125  F500.00
N17    Y74.2922
N18 G3 X170.6625 Y93.3422 I170.6625 J74.2922
N19 G1 X67.4625
N20 G3 X48.4125 Y74.2922 I67.4625 J74.2922
N21 G1 Y25.6922
N22    X40.2878
N23 G0 Z10.0000
N24    X203.8787 Y21.1578
N25    Z9.5000
N26 G1 Z0.0000  F300.00
N27 G98 Z10.0000
N28 G81 X203.8787 Y21.1578 Z0.0000 R10.0000 F500.00
N29 G0 X221.0625 Y0.0000
N30    Z9.5000
N31 G1 Z0.0000  F300.00
N32 G80
N33    Y13.6922  F500.00
N34    X238.1250
N35    Y110.1672
N36 G3 X211.1375 Y137.1547 I211.1375 J110.1672
N37 G1 X26.9875 Y137.1547
N38 G3 X0.0000 Y110.1672 I26.9875 J110.1672
N39 G1 Y13.6922
N40    X17.0625 Y13.6922
N41    X17.0625 Y0.0000
N42 G0 Z10.0000
N43 M5 M9
N44 X0.0 Y0.0
N45 G40G80M30

thank you

36
LazyCam (Beta) / Re: lazycam
« on: June 27, 2006, 09:21:02 AM »
where we change g93 to g94 in settup
thank you

37
LazyCam (Beta) / Re: lazycam
« on: June 26, 2006, 06:26:19 PM »
mach 3 ver 1.090.053
lazycam ver 2.54

mach3 error
f word with inverse time arc move on line number #11
no rate plunger on z
is it some think on my side or

N1 (File j2 )
N2 (File Posted in Mill Mode)
N3 (Monday, June 26, 2006)
N4 G90G80G40 G90.1
N5 M6 T2
N6 G43 H2
N7 G0 Z10.0000
N8    X54.7625 Y12.0000
N9 M3 S1000
N10    Z0.0000
N11 G1 Y60.6000  F5000.00
N12 G2 X73.8125 Y79.6500 I73.8125 J60.6000
N13 G1 X164.3125
N14 G2 X183.3625 Y60.6000 I164.3125 J60.6000
N15 G1 Y12.0000
N16 M6 T1
N17 G43 H1
N18 G0 Z10.0000
N19    X17.0625 Y0.0000
N20    Z0.0000
N21 G1 X0.0000
N22    Y96.4750
N23 G2 X26.9875 Y123.4625 I26.9875 J96.4750
N24 G1 X211.1375
N25 G2 X238.1250 Y96.4750 I211.1375 J96.4750
N26 G1 Y0.0000
N27    X221.0625
N28 G0 Z10.0000
N29 M5 M9
N30 X0.0 Y0.0
N31 G40G80M30

38
LazyCam (Beta) / Re: lazycam
« on: June 25, 2006, 02:58:32 PM »
hi test on
lazycam 2.54 need info

G4 p0.0000 where we do setup for time
z plunge rare missing
and give  error f word missing


(File j2 )
(File Posted in Mill Mode)
(Sunday, June 25, 2006)
G90G80G40 G90.1
G0 Z10.0000
   X17.0625 Y0.0000
M3 S0
   Z0.0000
G4 P0.0000
G1 X0.0000  F5000.00
   Y96.4750
G2 X26.9875 Y123.4625 I26.9875 J96.4750
G1 X211.1375
G2 X238.1250 Y96.4750 I211.1375 J96.4750
G1 Y0.0000
   X221.0625
G0 Z10.0000
   X54.7625 Y12.0000
   Z0.0000
G4 P0.0000
G1 Y60.6000
G2 X73.8125 Y79.6500 I73.8125 J60.6000
G1 X164.3125
G2 X183.3625 Y60.6000 I164.3125 J60.6000
G1 Y12.0000
G0 Z10.0000
M5 M9
X0.0 Y0.0
G40G80M30
thank you

39
LazyCam (Beta) / Re: lazycam
« on: June 24, 2006, 04:59:59 PM »
you should have place to download lazycam i saw there is ver 2.54 i download last ver mach and it not inside so we could do some test

40
LazyCam (Beta) / Re: lazycam
« on: June 23, 2006, 11:22:11 PM »
i try mach3 ver 1.90.052 with lazycam ver 2.53
it look ok but one think is buy me is every time i use lazycam we have to enter feed rate plunge rate spindle
rapid hight for each layer and so it mush have one way to keep the info for outside
inside 1 inside 2 inside 3 and so
thank you
jacques lambert

Pages: « 1 2 3 4 5 »