Messages

21

LazyCam (Beta) / Re: lazycam

« on: July 10, 2006, 07:41:20 AM »

it will be very nice
soon it ready let me know
thank you

22

LazyCam (Beta) / Re: lazycam

« on: July 09, 2006, 10:15:07 PM »

the last lazycam is ok
could you put option for milling machine when we use drill g81 z will be plunge rate speed
jacques

23

LazyCam (Beta) / Re: lazycam

« on: July 09, 2006, 09:54:58 AM »

i anderstand your point but i think when the z axe go down it should be  going down at the plunge rate set up to reach  z0.00
it could be change on chain but we have to enter every time an if we forget z go down to fast
thank you
jacques

24

LazyCam (Beta) / Re: lazycam

« on: July 09, 2006, 09:16:35 AM »

let me know when you put on ftp server it important
the last nc file  was made  on last download from ftp
thank you

25

LazyCam (Beta) / Re: lazycam

« on: July 09, 2006, 09:14:15 AM »

let me know when you put on ftp server it important the i made was on last download from ftp
thank you

26

LazyCam (Beta) / Re: lazycam

« on: July 09, 2006, 08:00:39 AM »

it look better
one more think
line n8
line n20
the speed z go trow it sould be f1000 like line 11
on line n8 n20 the r12.0000 where this is come from it look like from rapid hight




1 (File cut232 )
N2 (File Posted in Mill Mode)
N3 (Sunday, July 09, 2006)
N4 G90G40G80 G91.1
N5 G0 Z12.0000
N6    X37.0742 Y5.3976
N7 G0 G98 Z12.0000
N8 G81 X37.0742 Y5.3976 Z0.0000 R12.0000 F3000.00
N9 G80
N10 G0 X189.7125 Y12.0000
N11 G1 Z0.0000  F1000.00
N12    Y60.6000  F3000.00
N13 G3 X170.6625 Y79.6500 I-19.0500 J0.0000
N14 G1 X67.4625
N15 G3 X48.4125 Y60.6000 I-0.0000 J-19.0500
N16 G1 Y12.0000
N17 G0 Z12.0000
N18    X203.8787 Y7.4656
N19  G98 Z12.0000
N20 G81 X203.8787 Y7.4656 Z0.0000 R12.0000 F3000.00
N21 G80
N22 G0 Z12.0000
N23 M5 M9
N24 X0.0 Y0.0
N25 G40M30G80

27

LazyCam (Beta) / Re: lazycam

« on: July 08, 2006, 10:39:22 PM »

find any solution
jacques

28

LazyCam (Beta) / Re: lazycam

« on: July 06, 2006, 10:40:47 PM »

problem 2.56
check
at the beagening line n5 it shoul put z to 10 and afetr move x an y break the tool on z

line 16 same think after finish cutting the part z sould be up beafore x an y move
 
on ver 2.55 it was ok only the 2 time hole was the problem




1 (File cut232 )
N2 (File Posted in Mill Mode)
N3 (Thursday, July 06, 2006)
N4 G90G40G80 G91.1
N5 G0 X37.0742 Y5.3976 Z10.0000
N6 G0 G98 Z10.0000
N7 G81 X37.0742 Y5.3976 Z0.0000 R10.0000 F3000.00
N8 G80
N9 G0 X189.7125 Y12.0000
N10 G1 Z0.0000  F1000.00
N11    Y60.6000  F3000.00
N12 G3 X170.6625 Y79.6500 I-19.0500 J0.0000
N13 G1 X67.4625
N14 G3 X48.4125 Y60.6000 I-0.0000 J-19.0500
N15 G1 Y12.0000
N16 G0 X203.8787 Y7.4656 Z10.0000
N17  G98 Z10.0000
N18 G81 X203.8787 Y7.4656 Z0.0000 R10.0000 F3000.00
N19 G80
N20 G0 Z10.0000
N21 M5 M9
N22 X0.0 Y0.0
N23 G40M30G80



tahak you

29

LazyCam (Beta) / Re: lazycam

« on: July 06, 2006, 06:59:55 AM »

if it fix send to me
thank you

30

LazyCam (Beta) / Re: lazycam

« on: July 05, 2006, 09:59:52 PM »

any new developement on lazycam last problem
thank