Hello Guest it is March 28, 2024, 03:41:46 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jlautomatio

Pages: « 1 2 3 4 5 »
11
LazyCam (Beta) / Re: inf lazycam 2.64 mach3 rc2.0.g
« on: October 04, 2006, 11:09:14 AM »
hi find some think it look like if i generate the gcode and change the directory it mist  the \
thank you

12
LazyCam (Beta) / inf lazycam 2.64 mach3 rc2.0.g
« on: October 04, 2006, 10:01:11 AM »
need info on new upload
my problem is when i generate g code with lazycam it generate like this
c:\mach3\gcodef09.nc
it should be
c:\mach3\gcode\f09.nc

13
LazyCam (Beta) / Re: lazycam
« on: August 22, 2006, 08:32:53 PM »
lazy cam ver 2.62

mill make error
N1 (File F02 LS )
N2 (Default Mill Post)
N3 (File Posted in Mill Mode)
N4 (Monday, August 21, 2006)
N5 G90G40G80 G91.1
N6 G0  Z10.0000
N7  X56.3495  Y12.7498
N8  Z8.0001

=======================

N9 [{SPINDLE}]                                  it should be       N9 M3 S1000

=======================

N10 G1  Z0.0000  F350.00
N11  Y60.6000   F500.00

thank you
Jacques

14
LazyCam (Beta) / Re: lazycam
« on: July 13, 2006, 10:32:53 PM »
yes yes yes yes sir
thank you
i will contact you next week
good job

15
LazyCam (Beta) / Re: lazycam
« on: July 13, 2006, 03:44:33 PM »
so let me know when it will be there
thank you

16
LazyCam (Beta) / Re: lazycam
« on: July 13, 2006, 06:49:24 AM »
i when to ftp tis morning 7 am and still ver 2.56
jacques

17
LazyCam (Beta) / Re: lazycam
« on: July 12, 2006, 08:26:50 PM »
i just download mach 1.90.64
and lazycam is ver 2.56
any mistaque or
thank you

18
LazyCam (Beta) / Re: lazycam
« on: July 12, 2006, 10:28:10 AM »

Block.Format("G%.d X%.4f Y%.4f Z%.4f R%.4f F%.2f",Cycle,ent->startx,ent->starty,Depth,RapidHeight,FeedCut);

feedcut i ask for milling when we use g81 feed cut will be plunger rate

 in lazycam
in layer control  the set up i made was
feedrate 3000
plunger was 1000


---------N11 G1 Z0.0000  F1000.00

---------N20 G81 X203.8787 Y7.4656 Z0.0000 R12.0000 F3000.00

the reason i ask this i cut plastic using the same router 1/8 bit

the feed to cut the part is good at 3000
but when the z axe go trow the plastif it as to be 1000 to make nice job

in the dxf file we will have is lot of drill hole and line curve etch.

tell me if it could be done it will be very nice to have done



19
LazyCam (Beta) / Re: lazycam
« on: July 11, 2006, 10:23:13 PM »
i think is not i chech and the one i donwload is 2.56 ver
thank you

20
LazyCam (Beta) / Re: lazycam
« on: July 11, 2006, 09:46:59 PM »
any idea when the new update with my modification
thank

Pages: « 1 2 3 4 5 »