Hello Guest it is May 29, 2024, 04:54:15 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Kristin D

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 »
11
General Mach Discussion / Re: Knee Mill Coolant Containment
« on: September 20, 2008, 01:24:14 PM »
And Monogrammed too!  :o

Kristin

12
General Mach Discussion / Re: Feed rate after tool change problem
« on: September 19, 2008, 09:26:19 PM »
Must be something like that, as when I start up Mach asks to press Cycle start after tool change, it runs at speed then, next change or possibly the third one, it goes into slow motion.

Kristin

13
General Mach Discussion / Re: RTFM
« on: September 19, 2008, 09:03:35 PM »
Think that should be PTFM! Which i have been meaning to do for a long time, but then how could we have so much fun with Hood?

 ;D

Kristin

14
General Mach Discussion / Re: Feed rate after tool change problem
« on: September 19, 2008, 07:41:54 PM »
Ted,

I've noticed the same thing going on, seems it gets back up to speed once it reaches the next point if I recall but I usually get impaitent and do a run from here thing.

Kristin

15
General Mach Discussion / Re: lic key
« on: September 19, 2008, 06:25:30 PM »
 ;D, Ka-Ching $$$$$$

16
General Mach Discussion / Re: Question on mach
« on: September 19, 2008, 04:27:31 PM »
Probably best ask that to Ray L. AKA HimyKabibble as he seems to have a grasp on it, I just remembered the thread and thought it was close to what you were asking.

Kristin :)

17
General Mach Discussion / Re: Question on mach
« on: September 19, 2008, 03:15:50 PM »

18
General Mach Discussion / Re: Spindle output not function
« on: September 19, 2008, 01:31:15 PM »
Marco,

Can you attach a sketch of your relay circuit & part number or relay type, it would help to answer your question.

Kristin

19
General Mach Discussion / Re: help please
« on: September 18, 2008, 04:17:48 PM »
Peter,

First thing you want/need to do is get something that can generate a DXF file, this is what I use and it's free:
http://www.plm.automation.siemens.com/en_us/products/velocity/solidedge/free2d/index.shtml

Once you have a DXF file it's really easy to let software make your files, I've been having good luck with Sheetcam TNG, which for the time being is free from Sheetcam.com and has no limits to the number of lines of code.

Kristin ;D

20
General Mach Discussion / Re: Home and/or limit switch
« on: September 16, 2008, 12:07:36 AM »
Hood,

Yup was on the "settings" page and I was able to overun the switches by .010 and not crash! ;D

Got all three axis figured out and zero'd with the "safe limit" keeping from crushing any now, Wonder if I should go buy Igor a Glock like Brett's Chimp, good lab assistants are hard to find but I wonder if armed lab assistants are worth having, normaly I am the only one armed in the shop and it would be a pity to loose that advntage! Perhaps a super soaker and I'll just leave a power panel open! :D

Kristin

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 »