Hello Guest it is February 17, 2020, 01:04:33 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - CNC-Steuerung

Pages: « 1 2 3 4 5 6 »
11
German / Re: Übersetzung
« on: April 04, 2008, 08:27:54 AM »
Hi Anthony,


its written with terrible hand writing, but here are those I could read....

1,2,3 Erdung: Earth potential
4,5,6 Nulleitung: Zero potential (in Germany Earth and zero potential are separated)
7: Strom ???: means the 220V power supply?
8: Fräse Strom: 220V power supply mill machine
9: Steckdose: 220V power supply power socket
10,11: Rele..?: Relay connectors
12: +12V: +12V supply
13: +5V supply
14: ?? Mase??: perhaps GND for +12V,+5V, for controller supply
15,16: +24V for motor supply

But    no guarantee!!!

Good luck and best regards,

Wolfram

12
VB and the development of wizards / Re: How to get the loaded filename?
« on: January 04, 2008, 04:44:46 PM »
Thanks for your fast reply,
but Ive doesnt understand it, sorry.. ???

The file is loaded and displayed. The whole file/pathinformation is displayed in
the "file" - label, placed on the screen with screen4...

regards,

Wolfram



13
VB and the development of wizards / How to get the loaded filename?
« on: January 04, 2008, 03:50:42 PM »
Hi,

is there any possibility to get the actual loaded filename as string in VB?

That would be a help for displaying if long pathnames does exist in your system, or for the
very nice "percent complete" function as descripted in another thread...

Thanks and regards,

Wolfram



14
Hi Scott,

your code is working well, but Ive attached the macro for you.

Best regards from Germany,

Wolfram

PS.. its not possible to upload *.m1s fils, please rename ist before using...

15
Hi Scott,

Systemwaitfor doesnt work while debugging in the VB-Script editor!

Ive inserted the code into a M~ macro and use it in my code.
That works very fine...

Good luck,


Wolfram

16
German / Re: Herzlich Willkommen im "Deutschen Eck"
« on: June 14, 2007, 03:35:30 AM »
Hallo Herbert,

das sind leider zu wenig Informationen, um Dir adHoc helfen zu können, aber ich äußere mal ein paar Vermutungen.

Ist die LPT2 eine einfache LPT oder eine mit kombinierter LPT/serieller Schnittstelle?
Dann ist es häufig so, daß die Ressourcen dieser Karte nicht unter LPT zu finden sind, sondern unter Multifunktionsadapter.
(Systemsteuerung).
Wenn die LPT2 dann mit der richtigen Adresse (der ersten in der Liste) eingetragen ist, sollte es gehen..


Wenn nicht, mehr Infos, dann schaue ich mal.

Gruß Wolfram

17
VB and the development of wizards / Re: Tool table file format
« on: May 14, 2007, 04:58:28 AM »
Hi Simon,

yes it will...

Wolfram

18
Modbus / Re: Problems with communication
« on: May 12, 2007, 06:28:40 AM »
Hi Graham,

thanks for the hint, Ive tested several Konfigurations the whole night, but no effect  :-[

Whats about the Plugin for Mach3, is it available and if, where can it be downloaded?


Thanks,

Wolfram

19
VB and the development of wizards / Re: Tool table file format
« on: May 11, 2007, 03:47:22 PM »
Hi Simon,

you can access the tool table with following G-Code:

G10 L1 P~ X~ Z~ (Description)

P = Tool Number
X = Diameter
Z = Offset

Best regards from Germany,

Wolfram

20
Modbus / Problems with communication
« on: May 10, 2007, 04:37:44 AM »
Hi,

Ive problems with communication of ModIO and Mach3.
If I read the Board with the Serial Control Monitor (57600 Bd) anything is ok, I got the correct data
of connected devices without any error (Status: no error).
The communicaton LEDs are flashing fine an without any timeouts.

But in the Mach3 ModBus Status & Control Window I got every second an timeout error...

What could be the problem, (Ive tested it on several PCs with same results..)

Best regards,

Wolfram

Pages: « 1 2 3 4 5 6 »