Messages

1

General Mach Discussion / Re: E stop won't reset on mach3

« on: July 17, 2022, 09:06:53 PM »

Any ideas where to start?
I'm  going to reroute new wire to the Estop switches.
Bypass all the old wires.
Then, check settings on the pins page.

2

General Mach Discussion / E stop won't reset on mach3

« on: July 16, 2022, 01:43:12 PM »

Hello,
I have a Hurco mill that was retrofitted in 2011.
It has ran great over the years.
After sitting idle (no power) for about 5 months,when I power it on the Estop won't  reset.
Both Estop buttons and wiring check ok.
The Estop light on my control panel stays lit up, and the main screen 'reset flashes'.
It has been so long since  I've  messed with the pins and settings in mach.
Can someone tell me which pins in the settings I can check/reset/ toggle?

Thanks  so much.

3

General Mach Discussion / When doing an emergency backup of mach what should be saved?

« on: November 07, 2021, 10:06:55 AM »

I recently had a scare where my computer that ran mach3 on my mill was acting up.
There is a copy of my .xml file on a jump drive, but since the build was so long ago, what screen pics. would be helpful?
My thoughts were to take a pic of each screen  with the current settings,too.
Any other advice or shortcuts  to help with this procedure.

Thanks,
Jack

4

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 11:23:01 AM »

I think you will find that Version R3.043.062 is the best one to use.

Tweakie.

Thanks for that info. Much appreciated.👍👍👏👏💯

5

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 02:43:57 AM »

Tweakie,
Thanks  for that  info.
When I searched Google,  it just showed the latest version on several host sites.
Will let y'all  know how update goes.

6

General Mach Discussion / Re: Wanting to upgrade mach 3 to a newer version

« on: October 16, 2021, 01:16:33 AM »

Any ideas where I can download a  newer version? Not necessarily  the newest, maybe something around 2013???

7

General Mach Discussion / Wanting to upgrade mach 3 to a newer version

« on: October 14, 2021, 08:57:55 PM »

My mill is using an older ( licensed) version of mach 3.
It seems that it's  around a 2010-2011  year edition. At the time of my retrofit, it was the latest edition.
It the past there was a few problems where the spindle wouldn't  reverse in auto tapping, etc.
What would be the latest upgrade that some of you would recommend?
Right  now I don't have the info on the computer that is running the system.
 That can be provided tomorrow if necessary.
Thanks in advance.

Jack

8

General Mach Discussion / Re: May need to change computer that runs my mach 3 mill

« on: August 29, 2021, 05:44:30 AM »

Thanks again for all the help.

9

General Mach Discussion / Re: May need to change computer that runs my mach 3 mill

« on: August 29, 2021, 04:17:35 AM »

Also, how hard will it be to change over my Mach license to the new computer?

10

General Mach Discussion / Re: May need to change computer that runs my mach 3 mill

« on: August 29, 2021, 04:16:38 AM »

Thanks  so much  for that  info. I have a 'docking station' that allows you you read/ backup/ copy a hard drive that is out of a computer.
 This will work great for setting up the new  computer.
Thanks again for the info!👍👍👍👍👍👍👍