Messages

961

General Mach Discussion / Re: Mach3 win7 32bit, movement only in one direction, what to do?

« on: February 08, 2018, 01:54:49 AM »

Do I need A other motherboard? Or is there A way to fix this and get 5 volt on the port. The powersupply of the computer is 12 and 5 volts so somewere on the motherboard iTS being redused to 3.5.

My suggestion would be to fit a PCI parallel port card which outputs the required 5 Volts TTL signal.

You can identify if your computer motherboard can provide 5V from the PCI slot and which PCI card you need to buy from the data presented here; http://www.machsupport.com/forum/index.php/topic,34848.0.html

Tweakie.

962

General Mach Discussion / Re: Mach3 win7 32bit, movement only in one direction, what to do?

« on: February 07, 2018, 04:38:42 AM »

Just expanding on what TPS has already said...

You should see approx. 0Volts on a direction pin when jogging in one direction and approx. 5Volts when jogging in the other direction.

Tweakie.

963

General Mach Discussion / Re: mach3 randomly doesnt follow the correct toolpath

« on: February 07, 2018, 04:31:08 AM »

Hi John,

By popular opinion version .062 is the one.

ftp://anonymous:guest@ftp.machsupport.com/Mach3/Mach3Version3.043.062.exe

Tweakie.

964

General Mach Discussion / Re: Nmotion Controller

« on: February 07, 2018, 04:00:24 AM »

I am not aware of any endorsement for this product by Artsoft - sounds like a bit of deception by the vendor in the sales description of the product.

Ideally you should contact the vendor or manufacturer of the product you have purchased for after-sales support but as others have found that support is sadly lacking in the cheap far-eastern products.
However, I have attached a copy of the usbmove.dll which I hope will enable you to proceed.

Tweakie.

965

General Mach Discussion / Re: G49 on Mach3 Mill

« on: February 06, 2018, 07:15:18 AM »

You have nothing to apologise for, it is a damn fine bit of code

I second that - excellent work Thomas.

Tweakie.

966

G-Code, CAD, and CAM discussions / Re: Mach3 Error when running G-code

« on: February 06, 2018, 03:51:50 AM »

Hi Gordo,

Your Gcode file runs through to the end just fine here so nothing wrong with that.

We had a similar problem to the one you are describing some years back when graphics memory was limited. If you are up for a bit of experimentation then try turning off the Toolpath Display (Diagnostics window) and running your Gcode file again. If it completes successfully then it indicates that you need more graphics memory.

Now that graphics cards with 1 Gig or greater are cheap and readily available perhaps fitting one of those would be the way to go.

Tweakie.

967

G-Code, CAD, and CAM discussions / Re: Circle is not a Circle

« on: February 05, 2018, 10:21:19 AM »

I am pleased that you have resolved the problem.

Tweakie.

968

G-Code, CAD, and CAM discussions / Re: Circle is not a Circle

« on: February 05, 2018, 07:54:13 AM »

Hi Mesp,

Some CAD/CAM software's create arcs in Incremental Mode whilst other create arcs in Absolute mode ( you would need to Google it but the difference is basically the positioning of the centre of the arc ).
The IJ Mode setting within Mach3 is Modal so to be sure of the correct outcome all Gcode files containing arcs should specify the Mode (G90.1 / G91.1) as appropriate. This way you can run Gcode that has been created with any CAD/CAM software without encountering the problem you had discovered. Look at the Gcode of the smiley, it contains G91.1 so I knew it would run OK on your setup.

Tweakie.

969

General Mach Discussion / Re: Steppers have no torque.

« on: February 05, 2018, 06:01:49 AM »

Do they have ferrite magnets?

Absolutely no idea.

I will contact Sonceboz and see what they have to say about the lifespan vs. torque of their motors - I think they only make round case types.

Tweakie.

970

General Mach Discussion / Re: Steppers have no torque.

« on: February 05, 2018, 05:23:01 AM »

The old round stepper motors relied on ferrite magnets for their power. After 5 -10 years the ferrites lose their magnetisation and the stepper motor loses its torque. I have a large box of old round stepper motors of all sizes ...

I hope not.   

All my steppers are round case and most, if not all, are now more than 10 years old. 

Perhaps there are Steppers and there are Steppers (mine are Swiss made, Sonceboz).

Tweakie.