Messages

811

General Mach Discussion / Re: Respect

« on: March 13, 2019, 10:16:48 AM »

Hi Bill,

I think everybody will agree with me - Thank you for your kind words.

812

General Mach Discussion / Re: Mach3 on Win7 32 bit BUT 64 bit processor

« on: March 13, 2019, 06:11:14 AM »

All is well that ends well 

813

General Mach Discussion / Re: Mach3 on Win7 32 bit BUT 64 bit processor

« on: March 13, 2019, 02:20:38 AM »

You will not be able to use the Parallel Port with a x64 processor even if the OS is 32 bit. I tried it with Win10 and caused a devastating crash. 

If that was the case, than Mach3 wouldn't run on most of the PC's it does indeed run on.

The issue is with Windows 8 and up, as mentioned above.
Most processors have been 64 bit for a very long time.

If that is the case then I stand corrected.

Tweakie.

814

Brains Development / Re: MODBUS and Mach3 Signals

« on: March 12, 2019, 08:36:12 AM »

Now I realize that no one will help me with my "problem". Thanks....

That is just not true.
There are many here that are willing to help - it is just that you are asking for something that is just not practical.

Tweakie.

815

Brains Development / Re: MODBUS and Mach3 Signals

« on: March 12, 2019, 07:16:35 AM »

Until now I have done many fine things with "old Mac3".... And I will keep doing...

Excellent 

816

General Mach Discussion / Re: Turning on the relay causes a 'limit switch triggered' error

« on: March 09, 2019, 10:01:21 AM »

I put in a value of 1000 and with that the relay would trigger properly and the job would start as well. However, I have started getting random failures with a 'Limit switch triggered' message. I then increased it to a value of 6250 (the equivalent of 250ms). With this, it still randomly stops but there is a significant delay now before the job fails - still randomly. The stepper wires are shielded but not the limit switches and the estop.

This confirms that it is indeed electrical noise and you now need to check your wiring layout to see where improvements can be made.

I think you have already identified the problem...
All inputs (limit switches, EStop, etc) should be connected with twin shielded cable (with the shield connected to a single point Earth at the controller end only). If you do this then you should be able to reduce the debounce value to a sensible value of about 500.

817

General Mach Discussion / Re: Turning on the relay causes a 'limit switch triggered' error

« on: March 09, 2019, 03:14:01 AM »

Sounds very much like electrical 'noise'.

Try increasing the Debounce Interval (Config. / General Config.) to around 1000 and see if that makes any difference.

818

Mach3 under Vista / Re: A Blue Question sign in device manager win7 32

« on: March 03, 2019, 07:14:51 AM »

Hi Stefanus,

Welcome to the forum.

Just a general note to all...
It would be helpful if images were re-sized to 800 x 600 before posting to the forum. This thread relates;  https://www.machsupport.com/forum/index.php?topic=24585.0

Tweakie.

819

Mach3 under Vista / Re: Win7 32 bits Mach3 with parallel port pulsing at 100K

« on: March 02, 2019, 04:52:30 AM »

(I intend to dual boot Win7 32bits and win 10 64bits)

By all means try but you will not be able to use the LPT Parallel Port on a 64 bit PC.

820

General Mach Discussion / Re: mastercam - mach3 5axis

« on: March 01, 2019, 03:19:13 AM »

Perhaps check out this thread;  https://www.machsupport.com/forum/index.php?topic=32107.0
or even contact Richard directly by PM.