Messages

3971

General Mach Discussion / Re: SERIOUS jog problem!

« on: May 29, 2013, 04:03:15 AM »

Hi Sam,

Same thing happens here with both versions fd and efb of the plugin.

However, I have not determined if this is a USS issue or a Mach3 issue ?? (obviously one or the other is sending out the un-requested series of step pulses).

Tweakie.

3972

General Mach Discussion / Re: MI2000 CNC machine from 19's year

« on: May 29, 2013, 03:32:32 AM »

Sounds like you may have an ‘Enable’ signal after all.

Assuming that the pin assignments on your LPT cable are ‘standard printer port’ then with the machine connected to your PC and Mach3 running change the ‘active state’ (hi / low), one at a time (and click Apply / OK after every change), for each output (1-9,14,16,17) to determine which pin and what state (hi / low) causes your motors to ‘lock’.

Tweakie.

3973

FAQs / Re: mach3 and maxnc 15 OL

« on: May 28, 2013, 05:26:00 AM »

Hi TL,

Looks like you have successfully identified the problem and come up with a possible solution all on your own. Good work my friend. 

I look forward to seeing some pictures posted of the things you make with your machine.

Tweakie.

3974

Mach3 under Vista / Re: Windows7 64bit -> Mach3 -> Smooth stepper -> Xylotex board v3.0 -> Machine ???

« on: May 28, 2013, 05:09:36 AM »

Can I just connect the parallel outputs from the Smooth Stepper to my Xylotex board ? ( i.e., Will the Smooth Stepper work as a simple USB to Parallel converter or should I have to do any interfacing circuit ?)

Hi Harish,

Yes, It is a straightforward connection and no additional interfacing should be required.
There is some setting-up to do in the SS config. but that is fully explained in their documentation. http://warp9td.com/index.php/documentation

Tweakie.

3975

Show"N"Tell ( Your Machines) / Re: The Laser Project.

« on: May 28, 2013, 02:06:43 AM »

Hi Sam,

Cast your mind back a while to when I was starting out with this project and having problems laser cutting acrylic with smooth edges.

Who was it that took the time to look at my GCode and discovered that my CAD/CAM created tool-paths were rubbish ?

Before your help. http://www.machsupport.com/forum/index.php?action=dlattach;topic=12444.0;attach=21730;image

After your advice. http://www.machsupport.com/forum/index.php?action=dlattach;topic=12444.0;attach=21738;image

You can’t tell me that you are having troubles with shoe laces.    

Tweakie.

3976

General Mach Discussion / Re: Machine movement

« on: May 27, 2013, 12:28:26 PM »

Is there a check to turn the slave on?

I am not an expert at this because I have never had occasion to actually do it but…

In Motor Tuning make the settings exactly the same for both the Y and A axes and save the settings for each.
In General Config uncheck the A-Axis so it makes the A axis Linear.
In Slave Axis select Y to A then restart Mach3.

You should now have both these axes slaved.

Tweakie.

3977

Show"N"Tell ( Your Machines) / Re: The Laser Project.

« on: May 27, 2013, 12:21:46 PM »

 

Tweakie.

3978

General Mach Discussion / Re: Machine movement

« on: May 27, 2013, 06:31:53 AM »

 

Tweakie.

3979

General Mach Discussion / Re: Hall of shame

« on: May 27, 2013, 06:26:06 AM »

Good point you have raised Marius.

New Mach3 licenses are sold directly or via approved agents – Obviously that particular Chinese equipment UK importer is an approved agent so my commendations to David for diligently checking his license details.

There will always be piracy and unscrupulous dealers in the same way as there will always be crime – it cannot be eliminated, but with cooperation from our community it can be managed.

Tweakie. 

3980

Spanish / Re: COMO CONFIGURAR MACH3 CON ESTA INTERFACE

« on: May 27, 2013, 05:45:13 AM »

¿Que es (Fabricante / modelo)

Tweakie.