Messages

3141

Mach4 General Discussion / Re: Can't get licence file to work on Windows XP & Mach4 2.2914

« on: August 19, 2016, 01:42:32 AM »

Log on to My Account http://www.machsupport.com/software/mach4/ then Manage My License.

Tweakie.

3142

General Mach Discussion / Re: ATTENTION: Chinese 6040Z Owners

« on: August 19, 2016, 01:36:26 AM »

I think this is a brilliant idea and I wish you every success but if the project was to go ahead then the whole thing would need to be ‘Open Source’.

(If the full details of the “Mod Kit” are openly made available to everyone then it is fine. If however, the full details are only available to those who purchase the “Mod Kit” then you would be selling a product which is not necessarily related to Mach3 and it would not be appropriate to advertise here).

A different Section of the forum may be more appropriate but let’s see how much interest is shown.

Just my opinion.

Tweakie.

3143

G-Code, CAD, and CAM discussions / Re: Issues with Excessive CV Rounding

« on: August 18, 2016, 04:25:29 AM »

If you increase X and Y axis Acceleration even at the expense of Velocity (which may have to be reduced) then it will reduce corner rounding and overall you should notice little if any increase in job time. It is quite a delicate balancing act to get it just right but give it a try.

Tweakie.


Addition:  Check out Mach3 CV Notes here http://www.machsupport.com/help-learning/product-manuals/

3144

Mach4 General Discussion / Re: UC-100 and Mach4

« on: August 18, 2016, 02:16:56 AM »

Looks like the pmdx only supports 4 axis.  I need 5 axis support.

Perhaps take a look at the ESS http://warp9td.com/
That will work 5 axis with either Mach3 or Mach4.

Tweakie.

3145

General Mach Discussion / Re: Change direction of the work area

« on: August 16, 2016, 05:41:26 AM »

Absolutely nothing wrong with your English sir - it is just my opinion that the topic is controversial only because many people will have different views regarding the origin and home positions.

but if I change the Direction Active Low state in the Config. / Ports & Pins / Motor Outputs. it will be mirrored then?

If +X moves the cutter to the right of the workpiece and +Y moves the cutter to the rear of the workpiece then it will not be mirrored.

Tweakie.

3146

General Mach Discussion / Re: Need help with Mach3 and W xp compatibility(or maybe wrong signals to pins)

« on: August 16, 2016, 04:15:00 AM »

Please check that your PC meets the minimum requirements shown here; http://www.machsupport.com/software/mach3/

Whilst a few may have had some success with the TB6560 boards there are many who have had nothing but trouble.
Perhaps not what you want to hear but my advice, if you are serious about CNC and want a machine which performs well, is to look toward using a better quality controller and one where the manufacturer provides information, service and backup. One such option may be the Gecko G540 (or similar).
http://www.geckodrive.com/geckodrive-step-motor-drives/g540.html

Tweakie.

3147

General Mach Discussion / Re: Change direction of the work area

« on: August 16, 2016, 03:55:53 AM »

I think you are going to get lots of differing views on this (perhaps controversial) topic.

Whilst the medium to upper range CAD/CAM software allows the home position (X0, Y0) to be in any corner (including centre) the basic CAD/CAM packages generally only allow the home position to be in the bottom left corner.

In my opinion, your machine should be set-up with X0, Y0 in the bottom left corner of the work-piece with +X moving the cutter to the right of the work and +Y moving the cutter to the rear of the work ( Axis direction can be changed by altering the Direction Active Low state in Config. / Ports & Pins / Motor Outputs ).

Tweakie.

3148

FAQs / Re: Motor Tuning / Re-install Mach3

« on: August 16, 2016, 01:57:14 AM »

Hi JR,

I guess something has gone wrong with your installation of Mach3.
Version .066 is probably not the best to be using (according to popular opinion) so I suggest you download version .062 then install that as administrator and see if that resolves the problem. Here is a direct link to the file ftp://ftp.machsupport.com/Mach3/Mach3Version3.043.062.exe

It should install directly over the top of your existing version but keep a safe copy of your license file (Mach1Lic.dat) and <your profile>.xml file just in case.

Tweakie.

3149

Share Your GCode / Re: I help! need some logo

« on: August 16, 2016, 01:30:21 AM »

I am pleased for you.

If the Gcode I posted produces a mirror image then your axis is reversed – this can be corrected by changing the Direction Low Active state of the axis in Config / Ports & Pins / Motor Outputs.
The direction of an axis movement in relation to a key press can be changed by Config / System Hotkeys / Jog Hotkeys.

The point to remember about all this is that true axis movement is the direction the cutting tool moves in relation to the work piece rather than the actual direction of movement of the machine slides.

Tweakie.

3150

Mach4 General Discussion / Re: UC-100 and Mach4

« on: August 15, 2016, 08:00:23 AM »

Will Mach3 run 5 axis independently without pairing axis?

Yes it will.

Tweakie.