Messages

2951

Tangent Corner / Re: Larning th hard way.

« on: December 31, 2016, 07:40:38 AM »

Found it 

Tweakie.

2952

Tangent Corner / Larning th hard way.

« on: December 31, 2016, 03:03:02 AM »

Just as a tip to othrs, whn th workshop nds claning tak car whn using th shop vac on th computr kyboard. It mad such a good job on min that I had to spnd about an hour going through th bag dust and shavings to find my missing kytops – and thr is still on missing. 

Twaki.

2953

Show"N"Tell ( What you have made with your CNC machine.) / Re: DIY CNC - Homemade.

« on: December 31, 2016, 02:46:16 AM »

Nice work Steve, thanks for posting the video.

Tweakie.

2954

Share Your GCode / Re: Can't Fix Stupid Video and File

« on: December 31, 2016, 02:22:38 AM »

  Thanks for sharing 

Tweakie.

2955

General Mach Discussion / Re: Z Axis will not go below about -1mm when running - but thinks its going deeper?

« on: December 31, 2016, 01:53:25 AM »

My thoughts are that Mach3 is running correctly and that your Z axis is stalling on the way down.
Try halving the Velocity and Acceleration settings in Motor Tuning for you Z axis (remembering to save the changes) and see if that makes any difference.

Tweakie.

2956

General Mach Discussion / Re: Reference all home nothing happening

« on: December 30, 2016, 08:31:56 AM »

Tweakie,
Please clarify. What is the "external motion device which can be purchased very reasonably"? And where would I look for them? I'm trying to sale my CNC Router and building a Joe's EVO CNC. I have a PC I can use on the EVO but it is 64bit.

Here are just a couple that come to mind…

UC100 http://cncdrive.com/UC100.html
SmoothStepper http://warp9td.com/

But, there are many more to choose from.

(Please be aware that the very cheap Chinese motion control boards may not support all the Mach3 functions and also backup / support / software and firmware updates may not be available).

Tweakie.

2957

Share Your GCode / Re: eifel tower.dxf

« on: December 30, 2016, 03:24:40 AM »

Sorry, but I had no idea of your exact requirements.

Tweakie.

2958

General Mach Discussion / Re: Reference all home nothing happening

« on: December 30, 2016, 01:35:27 AM »

Something to consider...

Mach3 will run on any Windows OS from Windows 2000 through Windows 10. The parallel port driver included with Mach3 will only work with 32-bit DESKTOP computers (Laptops are not supported) with versions of Windows 2000 through Windows 7, but will not work with any 64-bit version of Windows or with Windows 8. Windows 8, 10 and 64 bit versions of windows require an external motion device which can be purchased very reasonably.

Tweakie.

2959

General Mach Discussion / Re: Reference all home nothing happening

« on: December 29, 2016, 07:51:30 AM »

First step is to run DriverTest.exe (Mach3 folder).

Does this run correctly ?

Post you .xml file (<your profile> .xml ) then we can check your settings & look for possible errors. You need to copy the .xml file from you Mach 3 folder then rename it to  tlittler.xml then use the Additional Options... to attach to your post.

Tweakie.

2960

Share Your GCode / Re: eifel tower.dxf

« on: December 29, 2016, 06:03:56 AM »

This one is intended to be laser cut from 3mm MDF or Ply.

Tweakie.