Messages

2111

Forum suggestions and report forum problems. / Re: "Preview post" not working ?

« on: April 22, 2016, 04:48:27 AM »

Works fine here (using Win10 and Safari).

Tweakie.

2112

General Mach Discussion / Re: Hot Stepper motors

« on: April 22, 2016, 02:01:58 AM »

Steppers are usually run at their rated current and they do get hot.

As a general rule they should not get so hot that you cannot briefly hold your hand on them (maximum case temp. around 65 deg.C).
It could be that the manufacturer of your steppers was over generous with the rating and if you find that they really are getting far too hot then reduce the current (reduce the resistor values to 2k2 or 2k).

Tweakie.

2113

Spanish / Re: El mach3 me corta pero no respeta las medidas

« on: April 20, 2016, 07:18:01 AM »

buen día. me construí un router cnc y me quedo muy bien compre los kits que venden en china y todo funciona bien abro el control manual con el tabulador y corre bien pero cuando mando a trabajar con un archivo realizado con artam me lo pone bien el mach pero lo hace mucho mas grande como al 300% mas. alguien sabe a que se debe? ya le menie los controles de motores de configuración del mach y nada. en el mnual de la interface dice que debe estar los steps per en 2000, velocity 120, aceleration 4 y los step pulse en 5y asi lo tengo , ya le baje la velocity y nada, gracias por su ayuda

If Mach3 is set-up in millimeters and your CAD/CAM software produces the Gcode set for Inches then that could be the problem ??
Inserting G20 at the start of your Gcode file may resolve the issue.

Google Translate...
Si Mach3 es puesta a punto en milímetros y su software CAD / CAM produce el Código G ajustado para pulgadas entonces que podría ser el problema ??
Inserción del G-20 en el inicio de su archivo de código G puede resolver el problema.

Tweakie.

2114

FAQs / Re: C&c changing zeros mid program on its own

« on: April 20, 2016, 02:19:47 AM »

Your Gcode runs (using your .xml settings) just fine here and without any error. You appear to be using a rather old version of Mach3 - I am not certain that updating to a later version would make any difference but it is worth a try (use version R3.043.062 rather than .066).

Tweakie.

2115

FAQs / Re: C&c changing zeros mid program on its own

« on: April 19, 2016, 11:07:10 AM »

Please attach <your profile> .xml file -  the one from the Mach3 folder (typically Mach3Mill.xml). Copy and rename it to Solosys.xml and use the Reply tab and Additional Options to attach to your post. This file contains your machine settings and may throw some light on the problem.

Tweakie.

2116

General Mach Discussion / Re: Z Acceleration

« on: April 19, 2016, 02:07:57 AM »

One test you could perhaps do is temporarily half your Z axis Velocity and Acceleration in Motor Tuning then see if the same issue persists ?

Tweakie.

2117

General Mach Discussion / Re: Z drive confusion

« on: April 19, 2016, 02:02:16 AM »

Hi Vince,

Welcome to the forum.

The fact that it used to work good but now it doesn’t is a bit suspicious.

From what you say it is my understanding that…

If you zero the Z axis DRO and your dial test indicator then MDI a command Z 0.100 the Z axis moves ~ 0.1125 but the Z axis DRO now shows 0.1000 ?

It is unusual for a Z axis to move further than commanded on the way up (assuming there is not a counter-balance system in use).

Try the same thing on the way down. Zero everything then MDI  Z -0.100. Do you still get approx. the same error between the dial test indicator and DRO ?

Tweakie.

2118

Mach4 General Discussion / MOVED: y axis off centre after rotation

« on: April 18, 2016, 08:04:03 AM »

This topic has been moved to General Mach Discussion.

http://www.machsupport.com/forum/index.php?topic=32393.0

2119

General Mach Discussion / Re: Tool moving to random coordinates

« on: April 17, 2016, 03:17:19 AM »

Thank you I should familiarize myself with the manual properly

I don't think you can expect to learn it all (there are parts I still don't fully understand) but the combination of manual and hands-on experience seems to win out in the end. 

Tweakie.

2120

General Mach Discussion / Re: Tool moving to random coordinates

« on: April 17, 2016, 02:46:29 AM »

I can 100% confirm that when entering g0 then the axis and a number it moves to that location in work coordinates. So if you zero x and then enter g0x20 it moves 20mm in axis x and if you enter the same again it doesnt move at all. Is this abnormal?

That is exactly as is should be when working in Absolute mode. The X axis is already at X20 so no movement is necessary.

On the other hand, if you were working in Incremental mode then the X axis would move another 20mm.

This is all explained, much better than I can, in the Mach 3 Manual. http://www.machsupport.com/help-learning/product-manuals/

Tweakie.