Messages

1541

Mach3 under Vista / Re: Help with STEPS PER UNIT CALCULATOR

« on: October 05, 2018, 06:16:14 AM »

Or do you mean I should put the microswitches on the stepper to 1600 (200x8) and put "8" in Mach3 Motor tuning?

That is it exactly (sorry for my bad explanation).

Tweakie.

1542

Mach3 under Vista / MOVED: Pairing mach3 to my plasma

« on: October 05, 2018, 04:47:51 AM »

This topic has been moved to General Mach Discussion.

http://www.machsupport.com/forum/index.php?topic=38482.0

1543

Mach3 under Vista / Re: Help with STEPS PER UNIT CALCULATOR

« on: October 05, 2018, 04:45:44 AM »

Oh I see. That would mean I should set the steppers' microswitches to 1600 microsteps and put the same value in Mach motor tuning, right?

Thanks

No.
Set the microsteps to 8

Tweakie.

1544

General Mach Discussion / Re: Motor Driver issue

« on: October 05, 2018, 02:59:05 AM »

There will be no direct 'short' between the Pul- and Dir- connections on the driver.
However, the internal opt-isolators may incorporate pull-up/down resistors so the measured resistance may depend on your measuring device.

Tweakie.

1545

Show"N"Tell ( Your Machines) / Re: Controller and drivers

« on: October 05, 2018, 02:43:33 AM »

I think an external motion controller would be a better choice than parallel port operation.

You would need to find details of the existing motors and drivers as they could possibly be OK to re-use.

It certainly sounds like an interesting project to undertake.

Tweakie.

1546

General Mach Discussion / Re: Motor Driver issue

« on: October 05, 2018, 02:14:10 AM »

Just a suggestion...

Remove the Enable wires completely. At this stage they are not necessary.

Check in your Mach3 Motor Outputs that you have the X axis Enabled and the correct Port and Pin numbers set. Also Step Low Active set.

Also check in Port Setup that you have the Port Enabled and the correct Port Address set ( the port address for your PCI card can be found in Win. Device Manager).

Hope this helps,

Tweakie.

1547

Mach3 under Vista / Re: Help with STEPS PER UNIT CALCULATOR

« on: October 05, 2018, 01:44:03 AM »

Hi Sono,

The most common microstep setting is 8 (or 1/8th).

The Gecko website has some excellent explanatory tutorials; https://www.geckodrive.com/support/step-motor-basics.html

Tweakie.

1548

Mach3 under Vista / Re: Help with STEPS PER UNIT CALCULATOR

« on: October 04, 2018, 08:23:17 AM »

So if I understand it correctly, if my Ballscrew is 12mm diameter and 4mm Pitch and it has one start, Lead (mm/rev) value on the file should be 4, right?

Correct 

Tweakie.

1549

Mach3 under Vista / Re: Help with STEPS PER UNIT CALCULATOR

« on: October 04, 2018, 06:31:36 AM »

Hi ,

I see the confusion.

'Pitch' is the distance between the crest of adjacent threads and 'Thread Starts' are the number of individual threads.
Basically the calculation provides the distance the carriage moves from one complete revolution of the screw and this is defined as the 'Lead'.

You do not have to complete the lower part of the calculator to obtain the Steps per Unit.

Once you have established the correct Steps per Unit they can be checked by using the Axis Calibration feature on the Settings page.

Tweakie.

1550

General Mach Discussion / Re: Calling all post processors. ( Help me to help you )

« on: October 02, 2018, 04:42:13 AM »

hello all please i need help
i have bridge saw cnc for cut the marble stone 5 axis i will retrofit ro Mach3 and i have alphacam software i need some one help me for build post processor can made it under payment
Thanks for your help.

pop28

This thread should help; http://www.machsupport.com/forum/index.php/topic,3607.msg27085.html#msg27085