Hello Guest it is March 28, 2024, 12:24:49 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - CJEls

Pages: 1 2 3 4 5 6 7 »
1
General Mach Discussion / Re: Xp start up screen
« on: May 09, 2009, 03:26:13 AM »
Alll

Thank you

2
General Mach Discussion / Xp start up screen
« on: May 08, 2009, 02:38:45 PM »
Hi All ;D

A stupid question. How do you get rid off the Xp start up screen, in other words when the pc boots it displays the xp  start up screen  I want it to be a blank screen or any other pic. ???

3
General Mach Discussion / Feedrate overide not working on mach lathe
« on: April 23, 2009, 03:23:28 PM »
Hi All

Does all off you also have te same problem with mach lathe, the feedrate override does not work.

Please Help

CJE

4
Brains Development / Re: Spindle clamp unclamp
« on: March 24, 2009, 01:21:18 PM »
Hallo Scott

Is There any way off checking the macropump when the machine is on to see if it is running.I did a stupid macropump If input4 is on then switch output 4 on. That works fine as a macropump so I Know it is working.

CJE 

5
Brains Development / Re: Spindle clamp unclamp
« on: March 24, 2009, 01:05:25 PM »
Hallo Scott

i tried running the Macro but it does not work on my set up.Then openning the macro and stepping into it the output wil only switch on and off.  I did enable the mmacro pump in the gen config and restarted the system. Any other advise.

CJE

6
Brains Development / Re: Spindle clamp unclamp
« on: March 23, 2009, 03:46:36 PM »
Hallo Scott

Thank you for the reply. I do have a question or 2.
What is getoemled(164 ) and 165 ,is it cw and ccw led some were on the screens and is user dro2000 created by you also on a page I do not understand where you got these from because I tried to look with screen 4 but could not fine it on the1024 iset for a lathe or is this on one off your lathe screens

thank you
CJE

7
Brains Development / Lathes
« on: March 18, 2009, 03:20:03 AM »
Hi All

Does enyone have a lathing circuit that we can look at as a example of how it works.

Thanks
Cj

8
Brains Development / Re: Brain Timing and "Latches"
« on: March 17, 2009, 04:13:24 AM »
Hallo Scott

Do you have a example of a latching circuit.  How do you reset the latch.

Thank you

CJ

9
Brains Development / Spindle clamp unclamp
« on: March 17, 2009, 03:10:04 AM »
Hi All

Is it possible to write a brain that will latch when pressing a button to open the chuck on a lathe and stay open. You will have to interlock it with the spindle so you can not open it while the spindle is turning. When pressing the button again it should close the chuck again.






Thanks
CJ

10
General Mach Discussion / Re: What is your trade?
« on: March 03, 2009, 02:05:02 PM »
Hi All

My trade I qualified for is call Electronic Mechanician Some thing only the South Africans can think up. 60% electronics and 40% mechanical and all on cnc Machines. I left the trade and became a Boiler maker (steel construction and manufacturing worker). Then started a nc maintenance company,that lasted until my bookkeepers  did me in and I lost it. I am current an employee for Victor Fortune South Africa (service engineer). These days a lot off mechanical work (rebuilding spindles, scraping of slides etc)The Machines I have Is for My hobby flying Radio controlled planes

Enjoy Life it is short

Cobus

Pages: 1 2 3 4 5 6 7 »