Hello Guest it is August 13, 2020, 05:09:52 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - antony_vm

Pages: 1
1
General Mach Discussion / Re: Flame Cutting
« on: October 26, 2008, 04:02:10 AM »
Hi Jim,

I am looking for a kind of THC application as in a Plasma.

The M3 function is clear to me.

Is there any mechanism for the ignition and where to source the solenoid valves.

2
General Mach Discussion / Flame Cutting
« on: October 25, 2008, 03:38:07 AM »
Hi All,

Planning to assemble a CNC Flame cutting.

Does anyone know of a Torch height control for Flame cutting,

And how is the initial ignition done?

Regards,

Antony.

3
General Mach Discussion / Re: THC 300
« on: October 17, 2008, 09:45:49 PM »
By lowering the Z axis velocity, this will again reduce my Z axis speed during probing.....I want the probing speed to remain same.

4
General Mach Discussion / Re: THC 300
« on: October 17, 2008, 12:48:45 AM »
Thanks Scott

Got the THC running after a long time..

Everything is working fine...................... I would like to reduce the speed of the corrections done to the Z axis by the THC.

Regards,

Antony.

5
General Mach Discussion / THC 300
« on: September 30, 2008, 09:25:20 PM »
Hi All,

I have been using plasma for a while and recently decided to add a THC 300 to it.

the indexing operation is working fine with the torch,  but the program stips at M3

code and does not turn the torch ON, torch can be turned on

manually no problem with the signal from card to the relay.

6
Mach3 under Vista / Vista
« on: September 30, 2008, 07:11:09 AM »
Hi All,

Have been using a plasma for sometime.

Really impressed to see what mach can do with XP.

Now that MS decided to discontinue XP, will Mach be able to deliver its punch in Vista.

Any problems if I change to vista?

7
General Mach Discussion / backlash
« on: June 18, 2006, 10:27:59 AM »
Hai All,
I am setting up a router with a servo drive.
The problem i am facing is that the gearbox of the servo motor is having a backlash of 2degrees on the gear end.
I want to use the gear box and do not plan to use a timing belt.
So I plan to install the encoder to the shaft of the gear box and not the motor spindle.
Will this cause any unnecessary hunting of the system.
I plan to use a higher count encoder so that accuracy is not compromised

Regards,
Antony.
 

8
General Mach Discussion / ac servo motors
« on: June 18, 2006, 05:20:02 AM »
Hai All,

Could any one help me with the description about the AC Servo motors.

I think it has 3 in no of coils and so can I use a 3 phase AC induction motors with it.

With  the fanuc motors I have seen that they metion the frequency of the motors something like 400 hz.

Could any one help with this I am planning to use the AC servo drives from rutex so could anyone help me how to choose a suitable motor.

Regards,

Antony.

9
Post Processors / ArtCam
« on: May 31, 2006, 08:43:58 PM »
Hai All, :)

I have set up my router and i am using ArtCam,Could any one help me with how to set up the post processor.

Presently i have set it up as "camtech(inch)"

And till now i did not have any problem.

And i am planning to get s post processor for Mach

It would be very thankful if any one would help me

Pages: 1