Hello Guest it is March 28, 2024, 07:15:33 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - xiaonu

Pages: 1 2 »
1
CS-Lab / Re: Spindel Problems with IP-S and Enc.Module, false RPM
« on: October 18, 2017, 06:43:16 AM »
Adjust the gain and offset of the frequency converter(VFD) Or use the V / F with PG mode(VFD)
(Sorry for the poor Translate, i am in china。。。。)

2
SmoothStepper USB / SmoothStepper trouble。。。
« on: November 30, 2013, 12:21:31 PM »

1, mach3 modbus RTU controlled frequency by inverter, but when the drive starts, SS mistakes.
or,2, mach3 through modbus into 0-10V analog input to the inverter, inverter start, SS also appeared wrong

FTDI drivers to the latest version, Plugin is 17fd


Error returned from USB function FT_Write.
Error FTDI USB Driver Error
Error = FT_IO_ERROR
Bytes requested:64
Byees written:0

3
SmoothStepper USB / Re: SS siganl help
« on: July 31, 2013, 10:05:39 AM »
If there is no wiring it should not be enabled.

Brett
My SS circuit board connected to the usb data cable only。。。。


4
SmoothStepper USB / SS siganl help
« on: July 31, 2013, 08:30:22 AM »
why M3 home signal is on???The board No wiring ,But in the mach inside, M3 home  signal is on。。。。




5
Chinese / Õý°æÖÐÎÄ°æµÄmach3¸ú±¾²»Éý¼¶£¡
« on: May 16, 2008, 10:48:40 AM »
ÓÚ½ñÄ깺ÂòµÄÕý°æmach3¼ÓÃܹ·£¬²Å·¢ÏÖÉϵ±ÁË£¡1.Èí¼þ¸ù±¾²»Éý¼¶£¡2.¸ù±¾ÏíÊܲ»µ½Õý°æµÄ·þÎñ£¡3£¬¸ù±¾Ã»Óпͷþ£¡¹Ù·½ÍøÕ¾Ò²²»¸ºÔðÖÐÎİ棡
ËùÒÔ˵Éϵ±£¡
Æ¥·òÖ®ÑÔ£¡°®Õ¦Õ¦µØ£¡

6
Modbus / Mach3 flashing..........
« on: May 15, 2008, 04:01:04 AM »
by lots of test at finally I achieved the object that communication between mach3 and PLC modbus,thank u Scott so much!
but an other question:
1.by inputting the Brain Editor£¨Modbus input with "Serial Non-Plugin Enabled"£©
2.at the box of¡°1 Input Lobe¡±,I choose the ¡°comare Immediate¡±¡°Equal To 1¡±
3.which output is Botton¡°303- MPG1 MODE:0¡±
at the stakeout¡°BrainView¡±I can see the sentence of the programme is availability.
but when I press the button of the definiens input,mach3 always back to the picture,for example,in the ¡°Diagnostics¡±,press the button which has been defined, the mach3 screen will back to the ¡°Program Run¡±picture.
Why??

7
Modbus / Re: Mach3 modbus partnership?
« on: May 11, 2008, 11:30:01 AM »
In software, mach3, "Function Cfg's "---" setup serial Modbus control "---" Modbus Configuration"
question 1. "Address ModBus (var)" What does it mean ?What should be filled out ?Var =? Variable?
question 2. "# Of Registers" should fill in what ?
question 3. In mach3 "operating" menu below ,"Brain Edit.."-----click "brain edit" create a new document brn.Click the "Commands" - "Add", pop-up "Add Input" dialog,Click "ModBus" button,list: ModBus IO Selected
                                            Enter ModBus Address to use ___ (Here I filled out the PLC's modbus input address? If I input the corresponding I0.0 modbus address format for the 1 x Register, which is 10, should fill in here 10 ?)
                                          Input Output   Bit only____Bit0-15 (question,"Bit only" what's mean?)
                                         source
                                           MacroModbus Emulation
                                           serial Non-Plugin Enabled
                                           Serial Plugin Enabled
                                           TCP ModBus                        cFG#_____0-127

Which should I choose ?

what's "local Var"?(is Local variable?)
This PDF is my plc modbus address define.

8
Modbus / Re: Mach3 modbus partnership?
« on: May 11, 2008, 05:01:42 AM »
this is question vedio.
Can you gives me "setup modbus Vedio",?with the English explanation document??grateful extremely!!!

9
Modbus / Re: Mach3 modbus partnership?
« on: May 08, 2008, 07:29:28 PM »
How uses Mach3 the button or i/o with supports modbus plc to carry on the pair? Whether some mach3 and a modbus agreement comparison form?
For instance: Estop-->modbus0x0000
And I use one to support modbus PLC's I:0.0 electronic contact to make Mach3 Estop the input, known PLC I:0.0 receives an electric shock the modbus address is 0x0000, how establishes?
Thanks!
The Mach3 each function like ¡°X limit¡± button, how establish in MOdbus Configuration? Whether to cite how many examples to me?
Has all Input signals, Out signals in the mach3 correspondence modbus address form?


how in mach3 input output does signals correspond modbus?
Sorry, my English is disappointing

10
Modbus / Mach3 modbus partnership?
« on: May 03, 2008, 11:05:15 PM »
How uses Mach3 the button or i/o with supports modbus plc to carry on the pair? Whether some mach3 and a modbus agreement comparison form?
For instance: Estop-->modbus0x0000
And I use one to support modbus PLC's  I:0.0 electronic contact to make Mach3 Estop the input, known PLC I:0.0 receives an electric shock the modbus address is 0x0000, how establishes?

Pages: 1 2 »