Messages

1

General Mach Discussion / Re: Prev. seq. not yet complete

« on: October 28, 2010, 02:39:53 PM »

Hi TP,

Any idea where I can get hold of the Sterling methog/plugin you are referring to?  Could not find it on the "Downloads/Plug-ins" page.

:-(

Regards
Conroy

2

General Mach Discussion / Re: Prev. seq. not yet complete

« on: October 12, 2010, 01:05:27 AM »

Hi Rick,

Below, please see the reply from Brian Barker.  It appears to be a problem with the plug-in that Art wrote.  Apparently he has not had the time to fix it for us.....

From: Brian Barker
Must be a problem in the plugin.. This is something that Art made and we don't have the code for it .. Art would need to change the plugin and I am not sure if he is going too You can do a probe with the G31 command and save the points.. I think it is M45 or something like that that enables the saving of the points..

Thanks
Brian 


Conroy du Plessis wrote:>
Hi Brian,> > My original "subject line" read "HELP NEEDED WITH DIGITIZING WIZARD"> > In fact, I am not experiencing the problem described below when using > the Digitizing Wizard, however, when using the Probing plug-in, the > problem occurs.> > There are other users with similar problems. Please see the link below:> > http://www.machsupport.com/forum/index.php?topic=12268.new;topicseen#new> > > I have increased the debounce value to as much as 500, but still > experience the same message, "Prev. seq. not yet complete"> > Any ideas?

> > Regards
> Conroy

3

General Mach Discussion / Prev. seq. not yet complete

« on: August 08, 2009, 05:25:23 PM »

Hi guys,

I recently build a probe based on the "One-penny touch probe".  I am using pin 12 on my parallel port for the "Active Low" trigger and it triggers correctly on the "Diagnostics" screen.

I position the probe as suggested in the message screen and reset all axis to 0. I start the 3dProbe and select the option "Probe object with grid". 

The x and y-axis start moving in the positive direction.  After approximately 10 seconds (whilst still in the process of moving to the extent of my workpiece to be scanned), I receive the error message "Prev. seq. not yet complete". 

When I click on "OK", the probe moves briefly only for the "Prev. seq. not yet complete" message to appear again.  This continues non-stop with obviously no success at probing.

I am using R3.041 of Mach3 and version 2 of the Probing plug-in.  I would really appreciate any assistance in this regard.


Regards
Conroy

4

General Mach Discussion / Re: Probing Plug-in

« on: August 08, 2009, 05:10:35 PM »

Hi Lawrence,

I am experiencing the same issues with "Prev. seq. not yet complete".  Have you had any luck in solving your problem?

Regards
Conroy

5

Show"N"Tell ( What you have made with your CNC machine.) / Re: Celtic Cross from cherry wood

« on: October 28, 2007, 07:46:52 PM »

Brilliant design !! What software did you you use for the design of the cross?

6

General Mach Discussion / Re: Why won't the pins go low?

« on: September 30, 2007, 06:35:10 AM »

Has a similar problem. Motors ran using other software but could not get Mach 3 to run the motors until I activated the "Gecko half step mode" on the Config->Motor and pins tab

Hope this helps

7

General Mach Discussion / Re: HELP please Mach3 won't run my board

« on: September 30, 2007, 06:29:30 AM »

Try to activate the "Gecko half step mode" option on the Config->motor and pins tab

8

General Mach Discussion / Re: Mach3 Problem? How do I check to know?

« on: September 30, 2007, 06:27:28 AM »

Hi,

I had a similar problem until I turned on an option on the Config->Motor and Pins dialog.  The option is had to check was "G21 half step mode". (right hand side on first screen)

Hope it helps...

Conroy