Hello Guest it is May 07, 2021, 01:04:36 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SSIRON

Pages: 1
1
here is a sample.  It is for a 30 by 15 in oval.  It seems to almost stop as it transistion from one line to the next

test3)
G90
G20
G49
G0Z0.2500
M3 S15000
G0 X0.2501 Y15.4937 Z0.2500
G1   Z0.0400 F50
X0.2866 Y16.9981 Z-0.0036
X0.3998 Y18.4996 Z-0.0473
X0.5892 Y19.9924 Z-0.0909
X0.6717 Y20.4699 Z-0.1050
X0.5892 Y19.9924 Z-0.1191
X0.3998 Y18.4996 Z-0.1627
X0.2866 Y16.9981 Z-0.2064
X0.2501 Y15.4937 Z-0.2500
G2 X0.5892 Y19.9924 I29.5410 J0.0351 F100
G2 X3.0103 Y27.1952 I19.7952 J-2.6453
G2 X5.6221 Y30.0274 I7.3153 J-4.1258
G2 X8.7920 Y30.6713 I2.3823 J-3.6032
G2 X11.7484 Y28.8696 I-1.2736 J-5.4164
G2 X14.4533 Y23.9742 I-10.3456 J-8.9113
G2 X15.4108 Y11.0076 I-26.8353 J-8.5002
G2 X12.9897 Y3.8048 I-19.7952 J2.6453
G2 X10.3779 Y0.9726 I-7.3153 J4.1258
G2 X7.2080 Y0.3287 I-2.3823 J3.6032
G2 X4.2516 Y2.1304 I1.2736 J5.4164
G2 X1.9850 Y5.8552 I9.4055 J8.2753
G2 X0.2501 Y15.4937 I24.2326 J9.3373
G1 X0.2501 Y15.4937 Z-0.2500 F50
X0.2866 Y16.9981 Z-0.2876
X0.3998 Y18.4996 Z-0.3253
X0.5892 Y19.9924 Z-0.3629
X0.6717 Y20.4699 Z-0.3750
X0.5892 Y19.9924 Z-0.3871
X0.3998 Y18.4996 Z-0.4247
X0.2866 Y16.9981 Z-0.4624
X0.2501 Y15.4937 Z-0.5000
G2 X0.5892 Y19.9924 I29.5410 J0.0351 F100
G2 X3.0103 Y27.1952 I19.7952 J-2.6453
G2 X5.6221 Y30.0274 I7.3153 J-4.1258
G2 X8.7920 Y30.6713 I2.3823 J-3.6032
G2 X11.7484 Y28.8696 I-1.2736 J-5.4164
G2 X14.4533 Y23.9742 I-10.3456 J-8.9113
G2 X15.4108 Y11.0076 I-26.8353 J-8.5002
G2 X12.9897 Y3.8048 I-19.7952 J2.6453
G2 X10.3779 Y0.9726 I-7.3153 J4.1258
G2 X7.2080 Y0.3287 I-2.3823 J3.6032
G2 X4.2516 Y2.1304 I1.2736 J5.4164
G2 X1.9850 Y5.8552 I9.4055 J8.2753
G2 X0.2501 Y15.4937 I24.2326 J9.3373
G0   Z0.2500
G0 X0.0000 Y0.0000
G0Z0.2500
G0X0.0000Y0.0000
M5
M30

2
my mistake the issue is related to G2 and G3 codes

3
I am not new new as I have been watching the site for a bit.  When i check my box and found this message i did not think much of it.  Then I read the replies and I was shocked!  This is incedible.  I have obsessed about building cnc router and plasma cutters for decades.  Anyway I have done just that.  So my next exercise is to figure out what it is I want to build with the machines and build my business.  I live on a relatively small island off the west coast of British Columbia, Canada.  Here are a few links to what is happening in my shop.

All the best - Ron

www.saltspringcommunity.com/2010/high-tech-design-and-fabrication-on-fulford-farm/
www.saltspringcnc.com

4
G-Code, CAD, and CAM discussions / artcam pro 2008 jerky motion issue
« on: June 03, 2010, 11:36:14 PM »
artcam pro 2008 jerky motion issue

I am having some trouble getting smooth motion out of my router.  I am under the impression, i can not recall why, that cv does not work with arc moves.  I actually have two systems.  A plasma system where I had to change the posts in sheet cam from mach with arcs to mach with out arcs.  Seemed to be necessary to get smooth motion out of plasma table.  The router on the other hand is still aproblem.  The posts in Artcam does not offfer a post with out arcs.  I should metion I have limited exposure to gcodes.  I just know the problem is associated with the I and j codes.  ANyone had any insite to this work be greatly appreciated

Ron
www.saltspringcnc.com

5
Hi - Don't delete me
My name is Ron.  I have been automating industrial equipment, processes and plants for25 years.  Mostly PLC and Plant Wide Supervisory and Data Acquisition Systems but i have always been intrigued with CNC.  I am winding down in business and and have now successfully built a router, a plasma cutter and upgraded an engraver.  I have currently working on a 4 by 8 router and plasma cutter.     

Pages: 1