Hello Guest it is March 28, 2024, 05:52:41 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - RogerRetro

Pages: 1 2 3 »
1
PoKeys / Re: 57CNCdb25, Mach4 and Gecko540 m03-05 relay control problem
« on: October 23, 2016, 07:29:18 PM »
NeoTO,
Thanks, I sure didn't think that through very  well! That got the spindle working, but after setting that up,  the X axis quit moving. All else seems OK. I can't see any relationship there, but nevertheless... the problem follows when swapping motor connectors at the motors, or on the G540. I'm at a loss as to how to troubleshoot for loss of step/direct signals with the Pokeys interface.  This is my first experience with mach4 and Pokeys, and i can't seem to find any troubleshooting information. Any Ideas on this issue?
Thanks,
Roger

2
PoKeys / 57CNCdb25, Mach4 and Gecko540 m03-05 relay control problem
« on: October 22, 2016, 02:40:57 PM »
I have designed and built a small CNC PCB drill, controlled by Mach4, Pokeys db25, and Gecko540. I included two relays to control the spindle motor on/off, and a spare. M-codes will not affect the relays, but by inverting outputs (pins 1 and 17) pin activity, the relays will run the spindle motor when not in e-stop and stop on e-stop (and vice-versa).  This tells me that the relays are connected and working correctly. What is missing to get mo3-05 to toggle the relays?
Thanks,
Roger

3
PoKeys / Re: 57CNCdb25 Fast_USB Driver Not installing for Mach4
« on: July 08, 2016, 10:50:46 AM »
Nicely Done!

Thanks,
Roger

4
PoKeys / Re: 57CNCdb25 Fast_USB Driver Not installing for Mach4
« on: July 02, 2016, 03:11:49 AM »
Good.
Adding a Mach4 version of that in the Mach4 section would work for me...
Thanks,
Roger

5
PoKeys / Re: 57CNCdb25 Fast_USB Driver Not installing for Mach4
« on: July 01, 2016, 12:03:39 AM »
NeoTO,
that installed the driver, no more Mach4 crashes.

I was unable to find reference to that setup file on  the PoKeys website...

Thanks again,

Roger

6
PoKeys / 57CNCdb25 Fast_USB Driver Not installing for Mach4
« on: June 30, 2016, 01:47:26 PM »
I have a Pokeys 57CNCdb25 connected (USB) to Win10 laptop with mach4 running.

I'm trying to set up the Pokeys without a (G540) drive controller connected.

I Installed required files into plugin folder per instructions.

Mach4 crashes when saving configuration, and when restarting Mach4, configuration dialog exists, but not fully configurable.

Bulk interface appears in device manager with missing drivers noted when plugged into USB.

Fast_USB Driver/folders do not exist anywhere in the system.

Can Fast_USB Driver install without a drive controller connected?

What am I missing?

7
Mach4 General Discussion / Re: Comments about Mach4 in Demo
« on: April 24, 2014, 10:57:49 PM »
Tool Path Limits persistence would be good for me...
Thanks,
Roger Blair

8
Mach4 General Discussion / Re: Comments about Mach4 in Demo
« on: April 24, 2014, 10:04:05 PM »
Very trivial considering, but...
Please include the standard colors dialog in the color editing popup.
Thanks,
Roger Blair

9
Newfangled Mill Wizard / Re: XY lead out when cutting circles - why?
« on: September 08, 2013, 10:33:24 PM »
Thanks for the support Ron,
just downloaded, I'll check it out tomorrow.
Regards,
Roger

10
Newfangled Mill Wizard / Re: XY lead out when cutting circles - why?
« on: August 30, 2013, 10:38:50 AM »
Thank you Ron,
Roger

Pages: 1 2 3 »