Hello Guest it is October 21, 2019, 04:19:09 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - chlluk

Pages: 1
1
Hi
Help needed here please,index pulse on diagnosic screen  is pulsing away perfectly but mach3 refuses to  engage threading. Just sits there ding squat .
No idea what to do next
Clive


2
General Mach Discussion / Re: hello everybody - motor drive question
« on: August 14, 2012, 11:46:42 AM »
Hi
I am looking for some help , Does anyone know what the general alogorithm or equation for controlling the motion of 2 or more axis is.
Looked just about everywhere.
Regards
Clive

3
General Mach Discussion / Re: Problem with XBOX 360 Pendant...?
« on: May 05, 2012, 07:14:55 AM »
Frustration beyond belief, cant get the wired xbox360 controller to work with mach3, have the latest version of mach3, have the latest active x loaded windows recoginises the pendant . The plugin is installed and is active as is the setup page for the plugin but at the bottom of the page on the right side it says not installed or recognised. Please dont tell me this is going in the trash can along with all the other chinese pendants and controllers that dont work with mach3. Any ideas before EMC2 goes up

4
Works in progress / Re: New (revised) Mach3 6-axis screen
« on: March 21, 2012, 07:53:11 AM »
Hii All
Am following the 6 axis screen topic with interest as I need a good working one for my 5 axis mill , firstly how do you make a screen is there a tutorial or document to explain the procedure and i notice on the 'Darc' download screen the manual jog panel only has 4 axis displayed. I would like to fix a few of these things myself just need the how to document.
Clive 

5
General Mach Discussion / Re: 0em functions
« on: June 18, 2011, 11:15:59 AM »
Hi
Im building a wire edm.
the electronic feedback unit on the machine monitors the burn cycle and requests the drive software to pause and then reverse a short way before continuing on with the job.
This is represented by a single line giving a a high or low logic level to the drive software.
Pause alone is not enough a small amount of backing of is reqd.
Clive

6
General Mach Discussion / 0em functions
« on: June 18, 2011, 10:03:33 AM »
Hi
I need help wrinting a macro or some other method to use the oem #297 (reverese)
activated by a high or low input on oem#1 pin
how do I go about it.
Clive

7
General Mach Discussion / mach 3 latest download
« on: October 03, 2007, 11:38:08 AM »
Hi
I have a version of Mach3 on my laptop that runs a machine tool just fine. However I have had need to transfer control to a normal PC with a more than adequote spec and I cant get a peep out of the parrallel port its just as if its in Demo mode. I have set the port config to normal AT mode and improved the machines spec according to the update sheet. The only difference is this version of mach 3 was downloded very recently after lockdown. Has the printer driver option been removed from the install page as i dont recall seeing it when installing the most recent download.
Regards
Clive

8
General Mach Discussion / Re: MAXNC10CL and MACH3 issues
« on: August 24, 2007, 11:13:04 AM »
Thanks Art
I will try the early *.xml file on the yahoo site destined for Mach2 and see how i get on.
Many thanks
Clive

9
General Mach Discussion / Re: MAXNC10CL and MACH3 issues
« on: August 24, 2007, 09:47:44 AM »
Hi
I too need to get my maxnc10 cl up and running but am bogged down. Where can I find the FTP site quoted that has the *.XML files for download. Cant see any links on the page or drop down menus to take me there. 

10
VB and the development of wizards / Getting started with VB
« on: July 26, 2007, 02:08:16 AM »
Hi
Can anyone point me in the direction of a document or listing on how to interface with mach 3 with a view to adding VB extras.
regards
Clive

Pages: 1