Messages

1

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 23, 2017, 08:01:03 PM »

Hi Overcooked,
Nice to see someone admit that they didn't know everything.

They guys from Vital are great to work with which is why I have been a happy user all these years.

lol thanks. this isnt the first of the last time that will happen!

For 7737, you can still use it to command motion to the drives without the encoder feedback.  you don't need the closed-loop activation to send the pulse train to the drives.  The signals available on RJ45 are drive enable, drive alarm, step+/-, Dir+/-, 5v, Gnd, 24v.

ya i realize that, i just didn't see the need to integrate it (7737) at this point because i couldn't really use the added functionality that board offered. plus i didnt have the RJ45 cables made up.

But i found all the connectors, cat 6 cable and the crimp gun, wired the drives and encoders into the 7737 and the motors still jog back and forth. =]

but the encoders dont seem to be being picked up by the 7737.

do i need the activation to see the encoders at all? am i looking in the wrong place? or is this another example of my lack of knowledge... 
i had one wired up to the smoothstepper so i have some idea that wiring/encoder is good.

once again, thanks!

2

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 23, 2017, 08:59:11 AM »

ok so, problem solved  . operator error is to blame for this one, well that and not having a proper understanding of what the software was looking for...

i had bought the 7737 expansion with the integra and never plugged it in because i hadn't bought the license for closed loop yet... however, it was enabled inside of the VSI device manager. once i found that setting i left it enabled, plugged in the 7737, and still nothing... imported a fresh copy of the Integra mach 4 profile and BAM!!!! off and running! the funny thing is the motors are still wired into the integra, the 7737 is just dangling by the ribbon cable with 24+ and the e-stop jumped out.

but who cares!!!! she runs!!!

now i just need to find that spool of ethernet wire and try running through the 7737, but i have a feeling it'll work just fine.

ok so, Vital Systems, thank you for your wonderful product, your assistance in this matter, and my apologies for the stupid on my part!

3

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 22, 2017, 06:33:58 PM »

what times are you guys available to remote login? (eastern std time)  im guessing you work the same hours i do?

4

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 22, 2017, 02:12:18 PM »

unfortunately rebooting everything didnt help.

but i have a suspicion it might be e-stop related. the command prompt that runs in the background of mach 3 keeps posting "mach external still set". which isnt super descriptive but it does seem significant. see attached image.

5

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 17, 2017, 06:31:28 PM »

Ricardo,

thanks for the super fast response!

profile the .m4prof imported fine, i can tell the inputs/outputs have changed. Control input and output came as MACHxx and Stepper.  but i still have the same problem. Cammand Pos and Following Error move with the jog buttons, but StepGen the DRO's and the motors sit at 0 =[

-Mike

6

HiCON Motion Controller / Re: STEPGEN = 0

« on: April 16, 2017, 06:45:43 PM »

to make sure im not crazy, i went back to mach 3 and the old USB smooth stepper and everything jogs back and forth and the DRO's move accordingly. 

7

HiCON Motion Controller / STEPGEN = 0

« on: April 16, 2017, 05:37:23 PM »

im currently in the process of converting my CNC over from a USB smooth stepper to the Integra, as well as from mach 3 to 4.

i have everything wired up properly  but none of the motors will budge. when i attempt to jog them in mach 4 the DRO's just sit at 0.

under Diagnostics-> Hicon i can see the Cammand Pos and Following Error move with the jog buttons, but StepGen and the DRO's sit at 0.

sounds like a missed a checkbox somewhere.

i tried to download the integra mach4 profile off the website, but the folder doesnt contain any *.m4prof files =[

any ideas?