Hello Guest it is March 28, 2024, 05:24:20 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jvdpulse

Pages: 1 2 »
1
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: March 30, 2017, 03:25:29 PM »
Hi there,
I've got a question. Whenever I start engraving, the machine engraves it in italic shape not straight! Does anyone know what's the problem with? :-[ :-[ ??? ??? :(

2
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: February 26, 2017, 05:34:46 AM »
Hi . Can help me anybody with a new and working engraving.dll ?For Mach3.
Thank you!
Hi u can use TOMTOM plugin for mach3

3
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: February 24, 2017, 11:54:30 AM »
Hi there,
I've got a question. Whenever I start engraving, the machine engraves it in italic shape not straight! Does anyone know what's the problem with?

4
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 30, 2017, 02:05:51 PM »
Will talk to him and ask if he allows
i sent for him Massage but he dont answer me yet.

5
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 30, 2017, 12:40:21 PM »
any body is here to be send plugin TOMTOM Tomura Kazuki for me?!! :'( :(

6
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 28, 2017, 03:36:44 AM »
You appear to have connected the laser power supply correctly.

Refer to my pdf document for setting up Mach3 for optimum results http://www.machsupport.com/forum/index.php/topic,16446.msg236132.html#msg236132

Tweakie.
Sorry. I read your document ,but I didn't understand!! Could you please send me your setting pictures of Match 3 ??

7
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 28, 2017, 03:16:52 AM »
how should I control the power of laser power supply while engraving??

In your case you have to stop the engraving, change the PWM (spindle speed), then start engraving again.

This is one of the reasons I have a manual control of laser power (as shown in my earlier diagram) - I can change laser power mid session.

Tweakie.

I have connected my board as you see in the following diagram to the laser power supply and I have allocated Digit Trig of Mach 3 to pin 16 and port 1, but when it is engraving with this plugin the laser power is  such a low that the engraved picture is unclear and i cannot set the laser power to solve this problem. when I measured voltage of wires which are connected to input power supply of TL and G while engraving, it's maximum is 0.30 or less. please kindly check the diagram to see whether connections are true or not??!



8
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 27, 2017, 01:08:36 PM »
how should I control the power of laser power supply while engraving??

9
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 27, 2017, 09:15:37 AM »
I succeeded to engrave! :) when the machine is engraving, the power supply makes a sound, something like cheep cheep! Is it ok if it makes this sound? Shall I be worried? ???

10
Mach SDK plugin questions and answers. / Re: Impact engraving plugin
« on: January 27, 2017, 03:14:01 AM »
Thanks a lot. Do you have the download link for plugin impact/engraving TOMTOM or the newest version of this??

Pages: 1 2 »