Hello Guest it is November 29, 2021, 01:33:24 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jon b

Pages: 1 2 3 »
1
General Mach Discussion / Re: Mach 3 auto zero script
« on: September 02, 2020, 04:42:20 AM »
Hi Twekie
 ive hit a wall trying to set up script for the z touch probe just cant get my head around it . could you possible fill in the blanks on your script ? . touch plate is 40.37mm
 maz z travel is 100mm
i think standoff distance above probe has to be greater than 40.37 mm ? beyond me im afraid .
 any information gladly received

2
General Mach Discussion / Re: touch probe install on mack 3
« on: August 30, 2020, 06:59:58 AM »
Thanks Tweakie
just checking don't know why i had a senior moment  ::) so as long as z zero is set up to table surface good to go ? . I have this already set in soft limits ...
Thank you

3
General Mach Discussion / touch probe install on mack 3
« on: August 30, 2020, 06:38:30 AM »
Hi i am installing a touch probe on my cnc its all wired up and functions just need to enter the script and should be good to go ,however i do not have a homing switch on my Z axis to set zero home position ? im guessing this is required for the touch probe to work or am i wrong

4
General Mach Discussion / touch probe install on mack 3
« on: August 25, 2020, 04:16:37 AM »
Hi guys please excuse  me if this is not directly connected to mack 3 but i would like to install a touch probe to the interface board on my cnc , my problem is i have used all 3 available inputs 10/13/15 for limit switches xyz . is there a way to loop the 3 switches to one available input thus freeing up 10 or 15 and how may i do this ?
kind regards Jon

5
General Mach Discussion / Re: Mach 3 auto zero script
« on: August 24, 2020, 10:33:25 AM »
Hay
thank you Twekie just the job  ;D

6
General Mach Discussion / Mach 3 auto zero script
« on: August 24, 2020, 05:45:47 AM »
Hi guys i am looking for a current version of the script to copy into mach 3 for auto zero probe metric version .can anyone point me in the correct direction.
regards Jon UK

7
Share Your GCode / Re: DELRIN
« on: January 29, 2019, 06:12:31 AM »
Hi Gerry
im using a machine supplied from a manufacturer in Poland image attached. A robust machine that has proved to make money so far . I guess this is a learning curve , checking out high rpm slow feeds was a starting point i need to find the sweet spot for this material

8
Share Your GCode / DELRIN
« on: January 28, 2019, 07:01:50 AM »
Not sure if this is the correct place for this post ?
Looking for advise on cutting Acetal / Delrin 12.5 mm thick . I im getting reasonable results at 20mm per second at 20,000 rev per minute 3 passed last pass .5 offset with a 6mm twin flute bit but Still minor chatter marks on the edge. The work piece is held down well so maybe a different cutter or feeds and speeds need adjusting ?

9
General Mach Discussion / Re: xml files to later version of Mach 3
« on: January 28, 2019, 06:56:12 AM »
SORTED  ;D

10
General Mach Discussion / xml files to later version of Mach 3
« on: January 26, 2019, 04:55:08 AM »
Hi guys
in the deep end here again just when you think things are going well .
My machine was built for me and supplied with what now appears to be an early version of Mach 3 VD1:90:065 ARGH  >:D pity the machine is a great build and works perfectly but the early version lacks some ability to set certain parameters
I already have a current version on my office pc that i purchased to learn the program .
My knowledge of computers is minimal although i have an outline idea of what to do i need some input on copying which files  over from the supplied memory stick ,these i assume being the XML files and the profile files created  by the manufacturer .
I was going to install the new version on the workshop pc and run it along side the older version until im sure i have things right

Pages: 1 2 3 »