Hello Guest it is August 13, 2020, 05:36:30 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - neptunier

Pages: 1 2 3 »
1
VB and the development of wizards / Re: macro for adjusting jog speed
« on: September 15, 2018, 04:57:25 AM »
crlf carriage return line feed at the end of the line, that was the problem.
thank you.

michael

2
VB and the development of wizards / Re: macro for adjusting jog speed
« on: September 15, 2018, 04:27:57 AM »
thanks, tps, what is CRLF?

3
VB and the development of wizards / macro for adjusting jog speed
« on: September 14, 2018, 12:52:22 PM »
hi everybody,

i was searching and trying a lot but i cannot find the solution.

i have a xbox attached to mach3 and i want two custom macros to set the jog speed. one for 100% and one for 2%. each macro should be activated with a button press. that way i can jog with one hand only the 2 speeds.

i tried creating a macro:
Call SetOemDro(3,2)

that should set the jog speed to 2%. i named that macro M799.m1s and put it in the right folder. when i want to try to execute the macro from the MDI it says scripter compile error in m799.m1s.

could anybody help here?

thanks,
michael

4
General Mach Discussion / SOLVED: shuttle pro older versions problems
« on: November 17, 2017, 10:34:15 AM »
my fault, i had to change to PID_5F3 and now it works like a charm.

5
General Mach Discussion / shuttle pro older versions problems
« on: November 17, 2017, 10:12:55 AM »
hello,

i just purchased an older shuttle pro, the silver one. i saw somebody use it in this video: https://www.youtube.com/watch?v=09HiUnPDeTY

i followed arts instruction pdf for installing the plugin and i tested before the shuttle and it works. however in the device manager it is not listed with the code that art says it would.

when i go on the config plugin screen for the shuttle i have the various options for the buttons. i used 3 for setx sety and setz. there are no options for the wheels. however nothings moves.

anybody could help?
thanks,
michael

6
General Mach Discussion / Re: shuttle wheel setting fixed
« on: September 28, 2016, 01:20:24 PM »
i found out, just dont hit enter in this field.

7
General Mach Discussion / shuttle wheel setting fixed
« on: September 28, 2016, 01:18:15 PM »
hello all,

i am setting up my backlash settings and i want to change the shuttle wheel setting it is set to 0.004s and i cannot change it.  :o

if i type in like 0.5 and press enter, the general config tab closes. on reopening, the setting stayed at 0.004.

i have installed a xhc handwheel and  but i deactivated the plugin if that has anything to do with that.

anybody an idea what is happening here?

thanks, michael

8
General Mach Discussion / SOLVED Re: how to configure the estop?
« on: September 24, 2016, 04:46:30 AM »
now it works and i feel really embarassed to tell the mistake. i used port 13 pin number 1  ??? , just switched the colums. i still had the order from motor outputs in mind, first the pins, then the port.

so anyway, thanks all for your help, now it is working perfect and my mill is complete. it is a 330kg artec zx45 mill, which i bought partely converted to cnc. yesterday evening i made my first steel chips :D

michael

9
General Mach Discussion / Re: how to configure the estop?
« on: September 23, 2016, 04:40:48 AM »
thanks. i am a few days off now, on my return i wil post the xml file.

10
General Mach Discussion / Re: how to configure the estop?
« on: September 23, 2016, 03:42:46 AM »
sorry for not being entirely clear with my descriptions.
i tried again, the led is lit and goes off if i press estop, no matter if i set active low or not.

Pages: 1 2 3 »